|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The Service Manual for Sansui AU-9500 was very helpfull, in complete and in good printable condition.
Thanks.
;
Dear Sir,
Document is original service document of sharp. I had a problem with the door contacts. Fuses where blown. With the manual in a few minuts is was clear what the problem was.
Manual was of great help.
With kind regards,
Martie Verhoeven
The Netherlands.
 ;
The scan is clear and well readable with very few weaker spots, usually on black background with white letters, but with enough zoom those spots can be read.
Printout is clear, the manual is complete and has all pages scanned.
I would give 5 stars, except that it is not in color, and the schematic and PCB pages are scanned on multiple pages. The document is locked (except printing) so the pages can not be extracted to compose them together for printing on the large plotter
It is worth the price tag.
;
let's say first that i do not need to have a credit for my opinion, i am a retired sparkie and i voluteerd to fix an electronic device for a local "Youthgroup",as no diagram was present i checked the "net" and gambled on this site and paying some fee via PayPall, i was gladly surprised that the manual arrived as was stated, GOOD SHOW, and best wishes, John
;
I had been looking for a Manual for my CS2150 for quite a while -- in fact I had just about given up. I saw this site and decided to download the Manual. When I Received it by Email I was really pleased with what I got, with the result that My Kenwood 'Scope is now 100% repaired and working well. As an AV Serviceman, you need a good 'scope, and thanks to this site, and the Service Manual, I have been able to repair it. The Manual was a copy of the Factory Original and the copy was very clear, especially in the area of the Circuit Schematics, where You really need to be sure of what You are looking at.
3.4.
3.4.1.
Carpet/Bare Floor Replacement
Removal
Selector
1. Place the carpet-bare floor pedal in the carpet position. Insert a screwdriver under the back of the pedal cover and pry up to remove it from the pedal assembly. Take care not to scratch the nozzle housing. 4. Insert the beater bar by placing the rounded portion of the end caps down into the slots in the nozzle base. 5. Press firmly, checking to see that each end is completely inserted.
2. 3. 4. 6. Check to see that the belt is centered on the belt pulley and that the beater bar turns freely. 7. Replace nozzle cover. 5. 6. 7.
3.3.
3.3.1.
Belt Replacement
Removal
NOTE: Every time the pedal cover is removed for any reason, it should be replaced with a new one. Remove nozzle cover as outlined in NOZZLE COVER section. Remove belt cover by removing screw at rear. Remove dust cover by removing eight (8) screws as outlined in MOTOR ASSEMBLY REPLACEMENT section. Remove belt and beater bar assembly as outlined in their respective sections. Remove lower plate assembly from the vacuum cleaner. Remove three (3) screws that secure carpet-bare floor
1. Follow all of the removal instructions outlined in the Beater Bar Assembly Replacement section.
shifter and handle release assembly. 8. Remove pedal shaft and remove handle release pedal. 9. Remove carpet-bare floor shifter assembly by sliding out through the top of lower plate.
3.3.2.
Installation
3.4.2.
Installation
1. Place the new belt around the motor shaft and follow the installation instructions in the Beater Bar Assembly Replacement section.
1. Slide the carpet-bare floor & handle release assembly back into the slot in the lower plate. 2. Insert the pedal shaft through the handle release pedal 3. 4. 5. 6. 7. 8. 9. and into the handle release assembly frame. Reinstall the three (3) screws that hold the frame and pedal shaft onto the lower plate. Reinstall the lower plate assembly on the vacuum cleaner. Reinstall dust cover with eight (8) screws. Reinstall the belt cover and screw. Install the new pedal cover by pushing it onto the pedal assembly until the tab snaps into place. Reinstall belt and beater bar. Reinstall the nozzle housing as directed in the NOZZLE COVER INSTALLATION section.
12
|
|
|
> |
|
