|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The AKAI 1720 model reel to reel tape recorder described in this Manual is quite an old unit - circa late 1960's. As a consequence, the description of the mechanical details - and adjustments thereof - is quite critical. The manual does this quite well. The schematics are also well presented and have detailed PCB overlays. Probably the only negative is that some half-tone detail has been lost from the original manual as it has been scanned in simple B&W.
 ;
Perfect source for service manuals: fast and professional transaction; high quality, perfect readable and largely scaleable PDF; complete schemes, diagrams and spare part list. Tnx a lot, cu again!!!!
;
I got your link from a friend and I must say that I am really satisfied with your service. Specially this B&O manual I didn't find anywhere on the web... but you could deliver it :-) . You deliver very fast and the copy is of good quality. So your webpage is bookmarked. Thanks
;
This was the Sony CCU-500A Service manual I was looking for.
The price was reasonable.
The permission to download was quck.
I will use Owner-Manual.com for all my manual needs.
;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
3.6.
3.6.1.
Hose Replacement
Removal
3.8.
3.8.1.
Motor Replacement
Removal
1. Remove the end of the hose from the tool holder. 2. Remove other end of the hose by depressing the two tabs which secure it to the back of the dust compartment.
1. Remove the dust cover by grasping the top near the onoff switch and pulling sharply out toward you.
3.6.2.
Installation
1. Install the new hose. Insert the hose adapter into the tool holder. 2. Install the new hose to the back of the dust container by pressing it into place until the tabs are securely locked into the dust compartment.
3.7.
3.7.1.
Motor Protector Replacement
Removal
2. Remove the lower plate, agitator assembly, belt, the plastic shaft, light bulb assembly and the nozzle housing as instructed in the respective removal sections. Remove the plastic holder. 3. Turn the vacuum over to the front side. NOTE: The dust container packing is positioned over the top of the motor case. Pull up on the portion of the dust container packing that lies across the top part of the motor case to free the motor case for removal. 4. Remove the five (5) screws from the motor case and then remove the motor case. 5. Disconnect the motor leads and remove the motor. Remove the motor support rubber (rear), noise suppressor, and the motor support rubber (front). Place these items on the new motor.
1. Remove the dust cover and dust bag. 2. Remove the motor protector cover, by releasing one of the tabs that secure it to the dust compartment,Take care not to break the tabs during removal. 3. Once the motor protector cover is out, the motor protector and protector spring are accessible for parts replacement.
3.8.2.
Installation
3.7.2.
Installation
1. Reinstall the motor protector and protector spring into the dust compartment. Replace the motor protector cover by applying pressure until both tabs snap into place.
1. Place the motor back into the dust compartment with brushes aligned parallel to the front edge of the dust compartment. The motor support (rear) must also align with the tabs in the same direction. 2. Rewire per the Pictorial Diagram. 3. Replace the motor case and the five (5) screws. 4. Replace the dust container packing by inserting it into the groove in the dust container. Use a screwdriver or a quarter to push the packing firmly into the groove 5. Turn the vacuum back over and replace the plastic holder, thick side out, plastic shaft, light bulb assembly, nozzle housing, belt, agitator assembly, and lower plate according to the respective installation instructions.
14
|
|
|
> |
|
