|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The service manual was a copy of the original from Wirlpool. The quality was good, all neccecary information was available including the service-codenumbers, so I could order the right part to be replaced for repair.
Downloding was no probem after the payment.
Thanks for the service!
;
Good,readable manual. I found other manuals that were not readable when it came to part ID, but the one downloaded from owner-manual.com was better than expected. I will do buisness with owner-manual.com again.
;
Service Manual that I received was very helpful to me. Thank you.
;
The manual is well organized and is easy to read. The chapters are following normal way to proceed.
;
This scanned manual is well done in that most all the pages except for one is straight and clear- the way I would do them. One page was upside down but that happens. For the money that is charged on this site you get a pretty good deal. Now with complex repairs, I still prefer to us paper manuals which I have to buy at stereomanuals but the one I got here was much less than the $45 he was charging but this is a larger than normal manual for three different units. I am a picky manual user because I have used original manuals from Sony and Teac.
CORD REEL ASSEMBLY REMOVAL/INSTALLATION
Removal
1. Lay vacuum with front down. Remove the four (4) screws that secure the cord reel cover, (Fig. 17), and then pull off the cord reel cover. 2. Remove the screw that attaches the cord reel bracket to the back of the dust compartment. 3. Turn unit over, taking care not to let cord reel assembly fall out, and remove the dust cover and motor case. 4. Remove the two (2) wire connectors and disconnect the red and white contact base assembly wires from the two (2) motor wires. Remove the cord reel by lifting the vacuum cleaner up and pulling the red and white wires through the hole in back of the dust compartment. NOTE: If the motor case cover is removed, DO NOT turn vacuum over, as the motor may fall out.
(Fig. 17)
EXPLODED VIEW (NOZZLE HOUSING)�
A BLOCK
Installation
1. To install cord reel assembly, reverse the removal process.
POWER CORD REMOVAL/INSTALLATION
Removal/Disassembly
1. Lay vacuum with front side down. Remove the four (4) screws that secure the cord reel cover, (Fig. 17), and then pull off the cord reel cover. 2. Take the cord guide out of the cord reel bracket and relieve tension on the cord reel spring by holding onto the power cord head while pushing down on the brake lever assembly. Continue the unwind until cord reel stops turning. NOTE: This is done to relieve tension on the cord reel spring and to prevent personal injury. 3. Remove the screw that attaches the cord reel bracket to the rear of the dust container. 4. Turn cord reel over and remove the center screw in back of contact base assembly. This will separate cord reel bracket from cord reel assembly. Unwind power cord all the way. 5. Place a flat-head screwdriver between contact disc assembly and tab on the cord reel hub assembly, (Fig.18), and gently pry contact disc assembly upward. This will separate contact disc assembly from the cord reel axle. 6. Slowly work contact disc assembly through the slot on the cord reel hub until contact disc assembly is separated from the cord reel hub.
(Fig. 18)
Installation
1. Insert contact disc assembly back into cord reel hub assembly, and place entire assembly on cord reel axle. Push down until it snaps into place. 2. Rewind power cord. 3. Place cord reel assembly onto contact base assembly and reinsert center screw. 4. Replace screw that attaches cord reel bracket to back of dust compartment. 5. Reset the tension on the spring and keeper assembly by pushing down on the brake lever assembly, holding power cord head and turning the cord reel clockwise eight (8) times. This will give the cord reel spring the tension that is required. 6. Replace cord guide. 7. Replace the cord reel cover and insert the four (4) screws that were removed.
- 20 -5-
|
|
|
> |
|
