|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The purchased manual is an high quality scan of the original Philips paper-based Service Manual. I am very satisfied!
 ;
The purchased manual is an scan of the original Panasonic paper-based Service Manual. Unfortunately the contrast is not perfect, but I am satisfied anyway!
;
The purchased manual is an high-quality scan of the original JVC paper-based Service Manual. The Service Manual includes the Owner´s Manual, so you do not have to buy both of them.
;
It paid to find this Service Manual, couldn't find it anywhere else. Exactly what I wanted. Received within 24 hours.
;
Complete manual with clear schematic diagrams and printed circuit board layouts of two variants of the headset and the transmitter an old and a new version.
Also shows how the headset and the transmitter is opened and how transmitter and receivers can be adjusted and where to measure.
I had no problems to repair the headset using this service manual.
ELECTRICAL ADJUSTMENTS
2-10: OSD HORIZONTAL 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-1) 2-13: TINT CENTER 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast, color and tint to normal position. 3. Connect the oscilloscope to TP024. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (27) on the remote control to select "TNTC". 5. Press the VOL. UP/DOWN button on the remote control until the section "A" becomes a straight line. (Refer to Fig. 2-2) 6. Receive the color bar pattern. (Audio Video Input) 7. Press the INPUT SELECT button on the remote control to set to the AV mode. 8. Using the remote control, set the brightness, contrast, color and tint to normal position. 9. Activate the adjustment mode display of Fig. 1-1 and press the channel button (39) on the remote control to select "TNTCA". 10. Press the VOL. UP/DOWN button on the remote control until the section "A" becomes a straight line. (Refer to Fig. 2-2) 11. Press the TV/DVD button on the remote control to set to the DVD mode. 12. Activate the adjustment mode display of Fig. 1-1 and press the channel button (51) on the remote control to select "TNTCD". 13. Press the VOL. UP/DOWN button on the remote control to set the same step numbers as the AV.
01 OSD 13
A 2-11: LEVEL
B
Fig. 2-1
1. Receive the VHF HIGH (70dB). 2. Connect the AC voltmeter to pin 6 of CP101. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (63) on the remote control to select "LVL". 4. Press the VOL. UP/DOWN button on the remote control until the AC voltmeter is 75 ± 2mV. 2-12: BRIGHT CENTER 1. Receive the monoscope pattern. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select "BRTC". 4. Press the VOL. UP/DOWN button on the remote control until the white 15% is starting to be visible 5. Receive the monoscope pattern. (Audio Video Input) 6. Press the INPUT SELECT button on the remote control to set to the AV mode. 7. Using the remote control, set the brightness and contrast to normal position. 8. Activate the adjustment mode display of Fig. 1-1 and press the channel button (30) on the remote control to select "BRTCA". 9. Press the VOL. UP/DOWN button on the remote control until the white 15% is starting to be visible 10. Press the TV/DVD button on the remote control to set to the DVD mode. 11. Activate the adjustment mode display of Fig. 1-1 and press the channel button (42) on the remote control to select "BRTCD". 12. Press the VOL. UP/DOWN button on the remote control to increase the step numbers by 5 steps to the AV. 13. Press the GAME button on the remote control to set to the GAME mode. 14. Activate the adjustment mode display of Fig. 1-1 and press the channel button (54) on the remote control to select "BRTCG". 15. Press the VOL. UP/DOWN button on the remote control to set the same step numbers as the AV.
"A" Fig. 2-2
D-3
|
|
|
> |
|
