|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a good quality scan of the Operation & Maintenance (Service) Manual for the PAL version of this high-band broadcast umatic, BVU-800P
All schematics and lineup procedures appear to be included in this one manual AFAICT.
The file size is just over 113 MB which gives an idea of the quality and number of pages.
All of the schematics, which contain some fairly small print, are easily readable when you zoom into the page.
John Thompson, Newcastle Upon Tyne, England.
 ;
Good quality, all schematics of few of models. There is also short form of user manual and regulation manual.
 ;
Perfect copy of the service manual. you can enlarge every page, and it comes up
with all details.
 ;
It´s very very nice manual with all, what i need. Original in good quality. Very fast business. Very much thanks...
 ;
Purchased the manual that I was looking for at a great price and could download it easily.. Great service experience and for future purchases I plan to use the site.
Thank you very much
MDCT-1000
� Connecting the LCD Controller with LCD
LCD controller WF LP XSCL YDIS YD AND CP LP DELAY LCD DF
3-4-2. LCD Dot Check (Lighting All Dots) Lighting all dots of LCD (Graphic data: By 0xff transfer)
04-02
LOAD
3-4-3. Checking the LCD Dot (Turning off all dots) All dots of LCD are turned off. (Graphic data : By 0x00 transfer)
04-03
FRAME
D0 D1 D2 D3
3-4-4. Test Signal Output from Microprocessor to LCD Controller Test signal output is under preparation.
04-06 NOW test signal loading...
XRES OR
DISP
Test signal is under preparation. 0xff and 0x00 are output repeatedly to the microprocessor ports D15 to D8 as follows.
Reset IC PA4 (Microprocessor)
3-4-1. Connection Check between Microprocessor and LCD Controller, and between LCD Controller and SRAM � Check the checksum of the font and the graphic data that are transferred to SAG1 (F000h to FFFFh) of the SRAM for display when releasing the STANDBY mode.
[Calculation is under way.] 04-01 (data read from LCD cntr) = ????????
About 0.25 S 0.25
0.25
0.25 About 30 seconds
The test signal output ends.
04-06 finished test signal output
3-5. Key Test: [KEY]
05-00 /* KEY TEST MANU */ 05-01 05-02 05-03 KEY INCREMENT TEST ANY KEY TEST K_mode LOG
� When [OK] appears: Connection between the microprocessor and LCD controller and the connection between LCD controller and SRAM are correct.
04-01 (data read from LCD cntr) = xxxxxxxx
[OK]
3-5-1. Key Test by Pressing Keys in Order
05-01 /* KEY INCREMENT TEST */ Turn ON � DISPLAY(A)
� When [NG] appears: 1. If the following *NG display is recognized, �XRD� is suspected. 2. If the following *NG display is not recognized (upon confirmation through trace monitor), either one of the connections between microprocessor and LCD controller or the connection between LCD controller and SRAM or the connection between LCD controller and LCD is defective. (At this time, if the test signal is output from the microprocessor to LCD controller in step 04-06, whether the connection is OK or NG can be confirmed, and also which of the connections between LCD controller and SRAM or the connection between LCD controller and LCD is NG.)
04-01 (data read from LCD cntr) = KKKKKKKK [NG] Mabye read pattern NG. or. [LCD_cntr]-[u_com],[h_sram]: connect NG
When the specified �DISPLAY (A)� key is pressed correctly, the following messages appear.
05-10 /* KEY INCREMENT TEST */
� DISPLAY(A) OK Turn OFF
19
|
|
 |
> |
|