|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
;
excellent value & price! Includes everything you need to know about the NN-C777! I would buy this again.
;
Very satisfied! I was searching for several days, but nope; till I discovered your webside and there it was at a very reasonable price. Keep up the good work!
Paul
Flanders
 ;
Generally speaking good copy; a few pages too hard contrast...
Good service and communication.
;
I purchased the unit from a private party and the original owners manual was not available. Having the ability to download it was extremely helpful and clarified operating the equipment immensely. This is a complicated unit and without the manual I would not have been able to maximize it's potential. Thank you.
SETTING THE CLOCK
In this example, the clock is set for the 24-hour (0:00) system.
7Press the ENTER button.
DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN kHz REC MHz SLEEP
2 4,6,8 1
8 Adjust the minutes by pressing the
3,5,7,9
button.
DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN kHz REC MHz SLEEP
or
q When the button is pressed once , the time will increase by 1 minute. When the button is pressed once, the time will decrease by 1 minute. q The hour setting will not advance even if minutes advance from "59" to "00".
1 Press the ON/STAND-BY button to turn the
power on.
9 Press the ENTER button.
DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN kHz REC MHz SLEEP
2 Press the CLOCK button.
DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN kHz REC MHz SLEEP
q The clock starts operating from "0" seconds. (Seconds are not displayed.)
3 Within 5 seconds, press the ENTER button.
DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN kHz REC MHz SLEEP
To see the time display:
Press the CLOCK button. q The time display will appear for about 5 seconds even if stand-by mode. Note: q The clock display will flash on and off at the push of the CLOCK button when the AC power supply is restored after a power failure occurs or after the AC power lead is disconnected. If this happens, follow the procedure below to change the clock time.
4 Press the
display mode.
DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN
or
button to select the time
"0:00"
�The 24-hour display will appear.
�(0:00 - 23:59) "12:00 AM" �The 12-hour display will appear. �(AM or PM 12:00 - 11:59)
To change the clock time:
"0:00 AM" �The 12-hour display will appear. �(AM or PM 0:00 - 11:59) q Note that this can only be set when the unit is
1 2 3 1 2
Press the CLOCK button.
first installed or it has been reset (see page 48).
Perform steps 6 - 9 above.
Within 5 seconds, press the ENTER button.
To change the time display mode:
Reset the microcomputer (see page 48). Perform steps 1 - 9 above.
5 Press the ENTER button.
DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN kHz REC MHz SLEEP
6 Adjust the hour by pressing the
DISC TOC TRACK MEMORY RANDOM TOTAL REMAIN kHz REC MHz SLEEP
or
button.
q When the button is pressed once, the time will increase by 1 hour. When the button is pressed once, the time will decrease by 1 hour. q When the 12-hour display selected, � AM � will change to � PM � automatically.
9
 $4.99 MDM2H SHARP
Service Manual Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…
|
|
|
> |
|
