|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a good quality scan of the Operation & Maintenance (Service) Manual for the PAL version of this high-band broadcast umatic, BVU-800P
All schematics and lineup procedures appear to be included in this one manual AFAICT.
The file size is just over 113 MB which gives an idea of the quality and number of pages.
All of the schematics, which contain some fairly small print, are easily readable when you zoom into the page.
John Thompson, Newcastle Upon Tyne, England.
;
Good quality, all schematics of few of models. There is also short form of user manual and regulation manual.
;
Perfect copy of the service manual. you can enlarge every page, and it comes up
with all details.
;
It´s very very nice manual with all, what i need. Original in good quality. Very fast business. Very much thanks...
;
Purchased the manual that I was looking for at a great price and could download it easily.. Great service experience and for future purchases I plan to use the site.
Thank you very much
MD-MS200W/MD-MS200/MD-MS200H
� Test mode check
Insert a high reflection (low reflection) disc, and once perform automatic adjustment in AUTO mode, and then check in MANUAL mode. Simultaneously observe waveforms of EFM(TP145), FEOUT(TP143), and TEOUT(TP144). Does the optical pickup move to outer/inner periphery when the / button is pressed? Yes Is tracking error offset measurement within allowable range? Yes Is focus error offset measurement within allowable range? No Yes Is laser power normal when laser lights? No Yes Does focus access occur in focus gain rough adjustment step? Yes Is adjustment out of allowable range? No Yes Check whether values of pins 10, 11, 14, and 15 of IC201, pins 30 and 32 of (IC101) (TP143) change when the / button is pressed. Check the pins 21 and 22 of IC101, the pins 6 and 52 of IC401, the periphery of Q101, Q102, and Q103, CNS101, and pickup flexible PWB insertion. No Check the pins 56 and 57 of IC201, the pins 25, 27, 29 and 30 No of IC601, the pins 10 and 11 of CNS601, and the slide motor terminal. Check Vref values of pins 3 and 4 of IC101 and pin 22 of IC201.
Check Vref values of pins 3 and 4 of IC101 and pin 22 of IC201.
No
Check the pins 52 and 53 of IC201, the pins 10, 12, 14, and 15 of IC601,and the pins 5 and 7 of CNS101.
Does the disc motor rotate in the same step? Yes Is focus servo applied in tracking gain adjustment step? Yes Doesn't the disc motor rotate at high speed in the same step? No No No
Check as stated in item "The disc motor does not rotate".
Check timing of pins 91 and 92 of IC401 and TP144(TEOUT).
Check EFM waveform of pin 23 of IC201 in case of high reflection. Check ADIP waveform of pin 4 of IC201 in case of low reflection.
Yes Is tracking gain adjustment within allowable range in the same step? Yes Is adjustment within allowable range in tracking error balance adjustment step? Yes Is tracking servo applied in focus gain fine adjustment step? Yes Is slide servo applied in continuous playback step? Yes Is cluster address counted up continuously in the same step? No Yes Continued on the next page. � 39 � No No Check whether value of pin 20 of IC201 and TP144(TEOUT) changes or DC shift occurs when the / button is pressed. Check whether values of pins 16 to 19 of IC201 and TP144(TEOUT) change when the / button is pressed.
No
No
Check waveforms of pins 54 and 55 of IC201, pins 18, 19, 21, and 23 of IC601, pins 4 and 6 of CNS101.
Replace IC201.
Check waveforms of pins 53 to 56 of IC101 and pins 23 to 25 of IC201. (In case of low reflection check also the waveform of pin 4 of IC201.)
|
|
|
> |
|
