|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent transaction - clean document received - Thanks a lot
;
Manual is in German but complete. I needed this one to fix a long lasting problem with the internal PSU of the camera. Most of the capacitors begin to leak after a few years wich results in the inability to power on the camera. When you try to turn it on the power led flickers and the unit directly turns off. Thanks to this manual I was able to locate all bad cap's and to dis- and reassemble the camera without any problems.
 ;
We received the manual in a timely manner and it was exactly what we were expecting.
;
Excellant, finally this is want I need and searching for The service manual is fantastic and thank you to owner-manuals.com and its service. Price is reasonable. It's a bit slow on my end in downloading but manage to receive the whole manual without a break. once again, thanks.
;
Very good scanning quality. All schematics are very legible. Worth every cent !
MD-MT170E
Error Messages
ERROR MESSAGES BATT EMPTY BLANK MD
q q
MEANING The battery has run down. Nothing is recorded.
ERROR MESSAGES Can'tSTAMP
q
MEANING Stamp function does not work.
(Check the number of tracks.) Can'tWRITE DEFECT!
q q
(Replace the disc with a recorded disc.) Can't COPY
q
You tried to record from a copy prohibited MiniDisc.
Cannot save the TOC information correctly to a MiniDisc. The disc is scratched.
(Record using the analogue cable.)
q
You tried to record signals other than music (such as data). A track cannot be edited. DISC FULL Er-MD (**)
(If the recorded sound is not right, retry recording or replace the disc with a recordable one.)
q q
Can't EDIT
q
The disc is out of recording space. The microprocessor has reported a system fault and the unit is out of order.
(Change the stop position of the track and then edit it.) Can't PLAY Can't READ (*)
q q
You tried to play back a track that cannot be played with this equipment. The disc data cannot be read because the disc is damaged. HOLD LOCKED
(To have it repaired, go to the distributor where you purchased the unit.)
q q
The unit is in the hold mode. You removed a MiniDisc whilst recording or editing.
(Reload the Minidisc or replace it with another one.) Can't REC
q
Recording cannot be performed correctly due to vibration or shock. NO DISC
(Turn off the power before removing the MiniDisc.)
q
A disc has not been loaded.
Number or symbol appears in (*) position.
ERROR MESSAGES NO SIGNAL
q q
MEANING Poor connection of the digital cable. No output signal comes out from the connected unit to playback.
ERROR MESSAGES TEMP OVER
q
MEANING The temperature is too high.
(Turn off the power, and wait for a while.) TOC FORM (**)
q
(Use the AC power for the connected unit.)
q
There is an error in the recording signal.
The input signal has improper sampling frequency. You tried to record on a playback-only disc. The write protection tab of a MiniDisc is set to the protected position. You tried to record on a playback-only disc. Since a track number is currently being located or updated, the unit cannot accept your command.
(Erase all of the tracks, and then record again.) TOC FULL
q
PLAY MD PROTECTED
q q
There is no space left for recording character information (track names, disc names, etc.). The track has been protected from being erased.
Tr. Protect
q
q
(Edit the track with the device on which it was recorded.) ? DISC
q
SORRY
q
A disc which contains data other than music was played.
(Wait for a while and try the operation again.)
(A disc which contains nonmusic data cannot be played.)
q
There is an error in the signal recorded on the disc.
Number or symbol appears in (*) position.
�6�
|
|
|
> |
|
