|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This manual is for the usa model only. But it is clear
, accurate and comprehensive, including board layouts and schematics.
I found it extremely useful for my mitsubishi dp-86da, but the same diagram would also work for the realistic lab5000 and hi fi 80. Thanks.
;
Great to have extra resources for Service Manuals, Now days you can really not trouble shoot efficiently without one , Wayne at IRIONS TV & ELECTRONICS REPAIR Clearwater , Fl. 33755 727-446-7955
 ;
For five bucks you can barely buy a hamburger. Or for the same five bucks you can buy a service manual. Much more useful. (and better for your health, depending on where you buy your hamburgers).
Yes, there are free manual sites out there, but if they don't have what you want, you have to pay.
And five bucks isn't much. Not for full specs, schematics and adjustment and parts replacement procedures.
My only criticism is that grayscale illustrations aren't well rendered, but I've seen worse.
Schematics and text are clear.
I'll be happy to purchase from here again.
Mike
mikeinthemountains@gmail.com
;
Impressively thorough. Even the simple operators manual helped me "fix" one of the 2 CD players in the unit. This unit reads CD's from the top so they should be installed in the magazines "upside down" from typical CD players. The CD player service manual helped me unjam a stuck carriage because somebody transported the box laying down loaded with CD's. A little lens cleaning & the player now works well! Thanks for you help at a great price! Joe
;
I was skeptical at first but later found the manual to be good quality for the price. It took a couple hours to receive the email with the download link, well worth the wait. Thanks.
MD-MT80W/90W/90/90C
� The spindle motor fails to run. Does the head move
Does the waveform appear on the IC201 pins 24 and 25 after TEST mode AUTO2 completion and in this state? Yes
No
Check the IC201 periphery.
Does waveform appear on the IC601 pin 43? Yes Does waveform appear on IC901 pins 1, 2 and 23? Yes
No
Replace. IC601
No
L608, IC201, IC901, CN601 and flex, etc. soldering check
Replace the spindle motor.
� Recording/playback operation
Insert a low reflection disc, and ascertain audio output by normal playback, and then set TEST REC mode. Does the head move down, failing to start record even when the continuous record mode is set after address? No Does the RF waveform appear at TP201 (When monitoring the RF waveform, set to MSL:80H using the control setting item of EEPROM) when recording/Playback is performed No Does level of pins 86 of IC401 and pin 17 of IC101 change depending on record and playback? Yes Yes Yes Check voltage of pins 52 and 53 of IC201, pins 3, 4, 7, and 9 of IC651, pins 1 and 2 of CN601. Check whether disc is recordinhibited.
No
Check periphery of IC401 and IC101.
Is RF pattern output from IC201 pin 50? Yes Check whether there is any damage in IC101, periphery of laser diode. Check for defects of IC351 in head drive flexible PWB, head, flexible PWB.
No
Check for soldering failure of IC201 .
Is audio monitor output given in normal mode LINE IN record? No
Yes
Check waveforms of pins 8,10,11,12 of IC501, pins 70 to 73 of IC201.
Is waveform obtained on IC501 pins 2 and 3? No
Yes
Check whether the pin 13 of IC501 and the pin 59 of IC201 are in H state.
Is audio waveform observed on the pins 8 and 17 of IC703? Yes Check whether input waveform is observed on the pins 4 and 21 of IC703.
No
Does voltage on the IC701 pins 13 to 15 change in case of record VOLUME UP/DOWN?
� 41 �
|
|
|
> |
|
