|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Complete original Service Manual in good (scan) quality!
;
Very good manual. Plenty of service information including alignment instructions. Clear circuit diagram. Excellent, thank you.
 ;
Good morning, the service manual you sent me was perfect.
Your service and answering are excellent.
I recomend this service.
Best regards.
;
I had been looking everywhere for a proper service manual for this VCR. Everywhere else that has this available for download has a very light version. This is the full service manual with all aspects that would interest anyone looking for the service manual for the AIWA HV-MX100 Worldwide VHS VCR. Great quality (as always). A winner hands down. Best Quality.
;
Top quality manual. Covers all aspects you'd expect in a top quality service manual for this Panasonic VHS VCR. The manual resolution is high. Another top quality manual from the only site worth downloading manuals from! If you're looking for a manual for the PV-9662 VHS VCR, this is the one you'll want to get!
4-5. Temperature Compensation Offset Adjustment
Save the temperature data at that time in the non-volatile memory as 25 �C reference data. Note : 1. Usually, do not perform this adjustment. 2. Perform this adjustment in an ambient temperature of 22 �C to 28 �C. Perform it immediately after the power is turned on when the internal temperature of the unit is the same as the ambient temperature. 3. When D101 has been replaced, perform this adjustment after the temperature of this part has become the ambient temperature. Adjusting Method : 1. Rotate the AMS knob and display �TEMP ADJUST�. 2. Press the ENTER/YES button and select the �TEMP ADJUST� mode. 3. �TEMP = � and the current temperature data will be displayed. 4. To save the data, press the ENTER/YES button. When not saving the data, press the EDIT/NO button. 5. When the ENTER/YES button is pressed, �TEMP = SAVE� will be displayed for some time, followed by �TEMP ADJUST�. When the EDIT/NO button is pressed, �TEMP ADJUST� will be displayed. Specifications : The �TEMP = � should be within �E0 - EF�, �F0 - FF�, �00 - 0F�, �10 - 1F� and �20 - 2F�.
4-6. Laser Power Adjustment
Connection :
Laser power meter
Optical pick-up objective lens
Digital voltmeter
BD board TP (I + 5V) TP (IOP)
Adjusting Method : 1. Set the laser power meter on the objective lens of the optical pickup. (When it cannot be set properly, press the 0 button or ) button and move the optical pickup.) Connect the digital volt meter to TP (IOP) and TP (I+5V). 2. Rotate the AMS knob and display �LDPWRADJUST�. (Laser power : For adjustment) 3. Press the ENTER/YES button twice and display �LD $ 4B = 3.5 mW�. 4. Adjust RV102 of the BD board so that the reading of the laser power meter becomes 3.4 +0.1 mW. �0 5. Press the ENTER/YES button and display �LD $ 96 = 7.0 mW�. (Laser power:MO reading) 6. Check that the laser power meter and digital voltmeter readings satisfy the specified value. Specification :
Laser power meter reading : 7.0 ± 0.3 mW Digital voltmeter reading : Optical pickup displayed value ± 10%
(Optical pickup label)
KMS
210A 27X40 B0825
lop = 82.5 mA in this case lop (mA) = Digital voltmeter reading (mV)/ 1 (�)
7. Press the ENTER/YES button and display �LD $ 0F = 0.7 mW�. (Laser power: MO reading) 8. Check that the laser power meter at this time satisfies the specified value. Specification :
Laser power meter reading : 0.70 ± 0.1 mW
9. Press the EDIT/NO button and display �LDPWR ADJUST�, and stop laser emission. (The EDIT/NO button is effective at all times to stop the laser emission.)
� 40 �
n
|
|
|
> |
|
