|
Who's Online
There currently are 6016 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
I needed the manual immediately and I got it immediately. I couldn't find this manual anywhere else on the net. The site was easy to traverse, and the price was very reasonable. I'll definitely be back for any future needs.
;
I received a good service manual, with good resolution. Improve the instructions for the purchase because they are not well understood.
For the rest, so good.
Thanks Angel.
;
Very good documentation for the Grundig 2077 model (as well as similar 800/900/1000 series radios). The first two pages are a summary of reception specifications and output capability. The third page is the tuner dial indicator and dial cord routing diagram. the final ~5 pages are the schematics for the various models (including 2077). The scan quality of the schematics are good, adn can be easily read if zoomed in. The documents are in German, not English as stated. It would have been nice to have the tuning sequence and settings, and some trouble shooting materials... or component and wiring map.
;
Perfect like it was descriped, Perfect like it was descriped
;
Very good detail, all pages clear, exactly what I needed
1
2
3
4
7.1.3 SINGLE OPERATION METHOD Single operation method and input level.
A Note : Before the diagnosis, discharge the Amp power line. Connect the resistor of 100� or more between W301(VH+), W303(VH�) and GND (CN3003 Pin1) on the E-VOL ASSY. Refer to the next page about the points. The procedure and the input level of a single operation are shown below. 1. Short R84 with 1k� on the PRIMARY ASSY. 2. The power supply of the unit is turned on. 3. The terminal SPCONT (7 pin of CN3002) on the E-VOL ASSY is controlled by the following voltages. The initial state is �SP Relay is OFF� and �Sys. Mute is ON�. Apply DC+12V to SPCONT so that AMP can output to the speaker terminal. [ SPCONT ] CONT SP Relay Sys. Mute 0V OFF ON 5V ON ON 12V ON OFF
B
[ The Signal Input ] Note : This unit has the electric volume and this volume is only controled by U-com in the Receiver. So, please input the signal to the point after the electric volume output. Input Point R3101 R3102 Output Point Speaker Out Speaker Out Speaker Out Gain (1kHz) 36 dB 36 dB 36 dB Input Level(rms) Output Level(rms) 44.6 mV 2.8 V 44.6 mV 2.8 V This is matrix center, so only the phase differential part is outputted.
L ch R ch C ch C
R84 1k� Point
SIDE A
W
NDING
9 H6 W132 W141 W111 1 2 H5
RISK OF FIRE
H R83
G
D
PRIMARY ASSY
FU3
W133
TX WINDING CHK
/YPW WIRE JP
W147
W144 R92
C1
ON/OFF W114
8 PT NK
REPLACE FUSE AS MAR
W115
L1
ALL
W146
BINDER W117
C5
R84 1k� Point
TUBE SIDE
OPEN
D92 Q81 D93 R91 C84
SECONDARY
E
RY81
D88
CN6
SIDE
W140
D83
D87
C81
+9V W142
D89
Q83
W143
R84 AMP POW ON C83
D90
C91
D81
W155
W145 IC1 I 78M56 O W139 V+12UN
D82
D84 C82 D96
PRINTED SIDE
1.POWER ON/OFF 2.GNDD 3.UN5.6 4.AC
1 1
4
4
C75
OPEN SIDE
F
46
1 2
M-EV21
3 4
W116
CN7
KN1
W132 W111 MY/NV/NK
C3
H
1
1 3 3 C
|
|
|
> |
|