|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
complete part-lists and pcb layout, schematic diagram is good enlargable,
 ;
Excellent, fast delivery, excellent product. Good luck!
 ;
This manual is for the usa model only. But it is clear
, accurate and comprehensive, including board layouts and schematics.
I found it extremely useful for my mitsubishi dp-86da, but the same diagram would also work for the realistic lab5000 and hi fi 80. Thanks.
 ;
Great to have extra resources for Service Manuals, Now days you can really not trouble shoot efficiently without one , Wayne at IRIONS TV & ELECTRONICS REPAIR Clearwater , Fl. 33755 727-446-7955
 ;
For five bucks you can barely buy a hamburger. Or for the same five bucks you can buy a service manual. Much more useful. (and better for your health, depending on where you buy your hamburgers).
Yes, there are free manual sites out there, but if they don't have what you want, you have to pay.
And five bucks isn't much. Not for full specs, schematics and adjustment and parts replacement procedures.
My only criticism is that grayscale illustrations aren't well rendered, but I've seen worse.
Schematics and text are clear.
I'll be happy to purchase from here again.
Mike
[email protected]
MEX-R5 SECTION 4 ELECTRICAL ADJUSTMENTS
SERVO SECTION
If any of the following parts was replaced, perform the �IOP Check� and �E, F Signal Offset Adjustment� as mentioned below.
SERVO board
Ver. 1.1
E, F SIGNAL OFFSET ADJUSTMENTS
Connection:
oscilloscope (DC range)
Adjustments Location:
� Optical pick-up block (chassis (OP-DVD) complete assy or chassis (OP-DVD) sub assy) � Mounted SERVO board � SERVO board: IC4 R29, R30, R40, R41, R43, R44 R53, R54, R57, R58, R65, R69 RV1, RV2 Precaution Use the following tools and measuring devices. � Extension jig (Part No. : J-2502-094-1) between the SERVO board and the MAIN board � DVD test disc TDV-540C (Part No. : 7-819-098-53) � CD test disc PATD-012 (Part No. : 4-225-203-01) � Digital voltmeter � Oscilloscope � Accessory remote commander RM-X702 (E, Chinese model) RM-X703 (AEP, UK, Russian models) RM-X704 (US, Canadian models)
TP (E), TP (F) TP (AGND)
+ �
� SERVO Board (Side B) �
Procedure: 1. Connect an oscilloscope to TP (E) and TP (AGND) on the SERVO board. 2. In the standby status, press the [4] key of the remote commander. 3. Press the [5] key of the remote commander. 4. Press the [7] key of the remote commander for more than two seconds. 5. When the test mode is selected, a peep sound is generated and the LCD display becomes 6-digit hexadecimal number indication. (*1) 6. Playback the CD test disc (PATD-012). 7. Press the P key of the remote commander. 8. Adjust the RV2 on the SERVO board so that waveform level of oscilloscope becomes between 2.75 and 2.80 V as follows.
E Signal Waveform:
RV2 E Signal Offset Adjustment TP (IOPCD) TP (IOPDVD) TP (AGND) TP (F) TP (A5V)
TP (E)
RV1 F Signal Offset Adjustment
IOP CHECK
Connection:
digital voltmeter SERVO board TP (IOPDVD), TP (IOPCD) TP (A5V) + �
0V level: 2.75 to 2.80 Vp-p
9. Connect an oscilloscope to TP (F) and TP (AGND) on the SERVO board. 10. Adjust the RV1 on the SERVO board so that waveform level of oscilloscope becomes between 2.75 and 2.80 V as follows.
F Signal Waveform:
Procedure: 1. Check the IOP value of DVD and CD by label on the optical pick-up.
Optical Pick-up Label:
KHS-340B ******* $$$###
CD IOP value DVD IOP value
0V level: 2.75 to 2.80 Vp-p
2. Connect a digital voltmeter to TP (IOPDVD) and TP (A5V) on the SERVO board. 3. Playback the DVD test disc (TDV-540C), and make a note of the value of digital voltmeter. 4. Divide the measured voltage value by 16.5, and convert it into current value. 5. Check that the calculated value is within ±6 mA to the IOP value given on the label. 6. Connect a digital voltmeter to TP (IOPCD) and TP (A5V) on the SERVO board. 7. Playback the CD test disc (PATD-012), and make a note of the value of digital voltmeter. 8. Divide the measured voltage value by 16.5, and convert it into current value. 9. Check that the calculated value is within ±6 mA to the IOP value given on the label.
11. Press the [RESET] button on the MAIN board, release the test mode.
*1) In the TEST mode, if any abnormality occurred in the operation, for instance, by pressing a wrong key, press the [RESET] button on the MAIN board to reset the operation once, and then retry the operation.
MEX-R5
19
19
|
|
 |
> |
|