|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
;
I was impressed with the quality of service (frequent e-mails to let you know the status of your order), and the speed at which the download became available. The manual was a life saver and was not easy to track down. Thank you for such an excellent service.
;
the manual was just what i wanted it had all the revelent information required to operate the hifi .Iwould use any manual i downloaded for any item which needs a manual
;
Die gewünschte Bedienungsanleitung wurde vereinbarungsgemäß in deutsch bereitgestellt. Sie ist gut lesbar. Kein Kauderwelsch.
Danke für den Service.
;
GOOD SERVICE MANUAL GOT ALL THE INFO. THAT I NEEDED..
Specifying the speaker parameters
Use the remote for the operation.
x LFE � LFE *****: (0 dB) Level of the LFE (Low Frequency Effect) channel output. Range: OFF, �20 dB to 0 dB, 1 dB steps �OFF� cuts the sound of the LFE channel. However, the low frequency sound of the speakers are output from the sub woofer. ��20 dB� to �0 dB� settings allow you to attenuate the LFE signal. �0 dB� outputs the full LFE signal at the mix level determined by the recording engineer. x D.COMP. � D.COMP.: (STD) Dynamic range compression. Range: OFF, 0.1 to 0.9, STD, MAX �OFF� does not compress the dynamic range. �0.1� to �0.9� settings allow you to compress the dynamic range in small steps. �STD� reproduces the sound track with the dynamic range intended by the recording engineer. �MAX� provides a great compression of the dynamic range. x T.TONE (MHC-DP800AV only) � T.TONE: (OFF) Test tone output. Range: OFF, ON �ON� outputs the test tone from each speaker in sequence. Adjust the LEVEL and BALANCE parameters so that the volume level of the test tone from each speaker sounds the same using the remote from your listening position. Select �OFF� to turn off the test tone.
Notes
1 From your listening position, press
SPEAKER LEVEL.
Adjustable menus and parameters are described below.
2 Press v or V repeatedly to select the
parameter.
3 Press b or B repeatedly to select the
setting you want.
4 Repeat steps 2 to 3 to set other
parameters.
5 Press ENTER.
Tip
You can use the digipad instead of the cursor buttons (v/V/b/B).
Adjustable parameters
The default settings are in the parentheses.
x BALANCE � FRNT L___R: (center) Balance between the front left and right speakers. � (MHC-DP800AV only) REAR L___R: (center) Balance between the rear left and right speakers. Range: 6 dB (L) to 6 dB (R), 13 steps x LEVEL (MHC-DP800AV only) � REAR ** dB: (0 dB) Level of the rear speakers. Range: �6 dB to 6 dB, 1 dB steps � CTR ** dB: (0 dB) Level of the center speaker. Range: �6 dB to 6 dB, 1 dB steps � SW ** dB: (10 dB) Level of the sub woofer. Range: �10 dB to 10 dB, 1 dB steps
� When you adjust the level of the sub woofer, set T.TONE to �OFF�. � Dynamic range compression is possible with Dolby Digital sources only.
10
|
|
|
> |
|
