|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
More than pleased with my prurchase, very good product for the price.
;
Manual-link came 30 minutes after having paid for an extremely rare (40 years old) item (sony icr-120) and helped me to get the radio rework again. So really good help for me, fast and reliable delivery and -taken that into consideration- a very reasonable price for that service. So thanks again! Mike, Germany
;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
SECTION 1 SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. Cautions when replacing IC121 and IC171 on the BD board A change has been made from CXD2535BR due to a modification of IC121 on the BD board in this unit. Accompanying this modification, a portion of the nonü]volatile memory of IC171 (XC24CO1S) has been changed. Conversely, when IC121 has been replaced, use CXD2535BR and rewrite the contents of IC171. Contents of non-volatile memories CXD2535BR Address CXD2535BR 15 93 2D 1A 2E 1A Rewrite Procedure for Non-volatile Memory (1) With the power switched off and the power plug plugged into a socket. press the BASS/TREBLE button. CLOCK button, and MD button more than one at a time in order. (2)Rotate the JOG dial knob and display the �EEP MODE�. When you press the YES key, the display changes to show �EEP**@@�. (Here, **indicates the address, and @@ indicates the data.) (3)Rotate the JOG dial knob and display the �EEP 15 @@�. (4)When you press the CD SYNCHRO button, �EEP 15 @@>@@� is displayed so then turn the JOG dial knob to show ügEEP 15 @@>93� (5)Press the YES key and �COMPLETE� will appear for a moment and data shown as �EEP 15 93� is being rewritten. (6)Rewrite address 2D and address 2E, into 1A using steps (3) to (5) above. (7)When all changes are complete, press the NO key and display �EEP MODE�. (8)Press the REPEAT button. If no disc is loaded, the time is displayed, so unplug the power plug. If a disc is loaded, the disc is ejected, then the time is displayed. Unplug the power plug from the socket to end EEP rewrite mode. (See �How to end test mode� below.) Note: Changes in the contents of non-volatile memory are not reflected until the power is switched off, then on.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe more than 30 cm away from the objective lens.
ENTERING TEST MODE
When you press the DISP button, p button, and EDIT button at the same tilne, the system goes into key, fluorescent tube, jogr and LED check mode. r Fluorescent tube check All the lights light up. Then, each time you press the ENTER button, the display mode changes as shown below. nAll lit n partially lit l n partially lit 2
r
LED check When you turn the jog dial, the LEDS change froln all lit to individually lit. r Key check The EDIT/NO button puts the system into key/jog check mode . When you press a button, the number is counted up. However, pressing a button again that you already pressed does not count up the number. Turning the jog dial to the right increases the jog count display, turning the jog dial to the left decreases the jog count. When you have pressed all the buttons and �KEY= 0K� is displayed, pressing any button ends test Inode.
HOW TO END TEST MODE
Method : l Press the REPEAT button. 2 If no disc is loaded, the time is displayed. If a disc is loaded, the disc is ejected, then the time is displayed . 3 Unplug the power plug from the socket.
�4�
$4.99 MJL1 SONY Owner's Manual Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
|
|
|
> |
|