|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
TROUBLESHOOTING
P
lease make these simple checks before calling for service. Because charges for adjustment of customer controls are not covered under your warranty, these tips can save you time and money.
Things to Remember about the IR Blaster
The IR Blaster transmits commands to your accessory devices to carry out functions (POWER/STBY, PLAY, STOP, etc.). Therefore, you need to ensure that the IR Blaster�s remote sensor window is not blocked and that the IR Blaster is in a position to send its signal into the room, where it can bounce off of walls or objects and then to remote sensor windows of the accessory devices. The remote sensor windows of the accessory devices must not be blocked in order to receive transmissions from the IR Blaster. Light colors or other room conditions can prevent the IR Blaster signal from reaching accessory devices. Also, storing accessory devices in glass-covered cabinets can block the signal. If you have such conditions, IR Shooters can be attached to the IR Blaster cable for more direct transmission of the signal from the IR Blaster to accessory devices (see page 4). Call 1-800-851-8885 to order the IR Shooters.
Difficulty
A Philips Accessory Device Will Not Respond to Any of the Remotes Tested During Setup
Remedy
The remote codes of the Philips accessory device you�re attempting to set up may not be preprogrammed into M-Link� because the device is new. Go to the section �Setting up a New or Multibrand Accessory Device� and follow the steps to set up your Philips accessory device.
Remote Control Functions of Philips Accessory Devices Are Not Working or the Wrong Functions Are Being Activated When M-Link� Is Used Accessory Devices Will Not Respond When Macro Buttons Are Pressed
Different codes have sometimes been used for the same function among some Philips accessory devices. You may need to delete the device from M-Link� using the onscreen menu, and then explore the functions of the Philips accessory device using its remote control. Follow the steps under �Setting up a New or Multibrand Accessory Device� to have M-Link� learn the remote functions.
� Ensure that all of the setup steps have been followed for each accessory device. For the Home Video macro to work, a VCR must be setup; for the Home Movie macro, a DVD, LD, or VCD player; and for the ITR video, a VCR. See �Setting up a Philips Device� on page 7 or �Setting up a New or Multibrand Device� on page 10 for instructions. � After setup, these simple requirements need to be met for each button in order for it to operate: Home Video�a VCR tape must be inserted and rewound in the VCR player, and the VCR must be in standby mode. The macro may not work for an accessory device that is not turned ON by the POWER/STBY button on the device�s remote control. Home Movie�A video disc must be placed in the DVD, LD, or VCD, and the accessory device must be in the standby mode. The macro may not work for an accessory device that is not turned ON by the POWER/STBY button on the device�s remote control.
26
|
|
|
> |
|
