|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very satisfied! I was searching for several days, but nope; till I discovered your webside and there it was at a very reasonable price. Keep up the good work!
Paul
Flanders
 ;
Generally speaking good copy; a few pages too hard contrast...
Good service and communication.
;
I purchased the unit from a private party and the original owners manual was not available. Having the ability to download it was extremely helpful and clarified operating the equipment immensely. This is a complicated unit and without the manual I would not have been able to maximize it's potential. Thank you.
;
Being a user of older radios of many kinds, preferring them over more modern rigs, this manual was invaluable in the programming of my two. I now know for certain what the assorted buttons functions are, and am very grateful to have found this excellent site. Many thanks for your assistance, Tony.
;
Clear and easy to read. All details as expected. Price acceptable , and quick delivery.
5. Specify time-varying change in the tone
Use EG 1 to create time-varying change in the cutoff frequency (FILTER �Cutoff�). If you wish to use the front panel knobs to adjust the EG 1 parameters, use the SEQ EDIT [SELECT] key to make the SEQ 1�3 LED�s go off.
Cutoff Note on Note off
d. Adjust the speed at which the tone will change after the note is released
q Rotate the EG 1 [RELEASE] knob. The LCD screen will show Page 10D: EG 1 �Release.� Rotating the knob toward the right will make the sound change more slowly, and rotating it toward the left will make it change instantly.
10D EG1 Release:
000
c a b d
Time
6. Adjust the output of the timbre
a: Attack Time b: Decay Time
c: Sustain Level d: Release Time
a
a
b
c
d
b
a. Adjust the speed at which the tone will change during the attack
q Rotate the EG 1 [ATTACK] knob. The LCD screen will show Page 10A: EG 1 �Attack.� Rotating the knob toward the right will cause the tone to change more slowly, and rotating it toward the left will cause the tone to change instantly.
10A EG 1 Attack:
c
d
a. Adjust the volume of the timbre
000
If rotating the knob does not produce an effect, try adjusting the FILTER [EG 1 INT] knob, or make sure that the SEQ EDIT SEQ 1�3 LED�s are dark. If these LED�s are lit, it is not possible to edit the EG or LFO. The knobs will function to edit the sequence data.
q Rotate the [LEVEL] knob. The LCD screen will show Page 09A: AMP �Level.� If the volume changes over time, this level will be the maximum level that occurs during the change in volume.
09A AMP Level:
b. Adjust the speed at which the tone will change during the decay
q Rotate the EG 1 [DECAY] knob. The LCD screen will show Page 10B: EG 1 �Decay.� Rotating the knob toward the right (increasing the value) will cause a longer decay time until the sustain level is reached.
10B EG 1 Decay: 030
127
b. Adjust the output panpot (stereo position)
q Rotate the [PAN] knob. The LCD screen will show Page 09B: AMP �Panpot.� When the knob is in the center (CNT), the output will be centered.
09B AMP Panpot: CNT
c. Adjust the brightness of the sustained sound
q Rotate the EG 1 [SUSTAIN] knob. The LCD screen will show Page 10C: EG 1 �Sustain.� The change in brightness produced by the [SUSTAIN] knob will depend on the setting of the [EG 1 INT] knob.
10C EG 1 Sustain: 060
c. Select the envelope source for the volume
q Press the [EG 2 /GATE] key. Each time you press the key, the envelope source will change. If you want the volume change over time, select EG 2 ([EG 2/GATE] key LED dark). If you want the volume to sound at a �xed level, as on an organ, select GATE ([EG 2/GATE] key LED lit).
22
 $4.99 MS2000 KORG
Quick Start Quick start guide ( sometimes called quick guide ) contains most important information on how to use…
|
|
|
> |
|
