|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
manual de usuario perfecto y completo de buena calidad de impresion y muy detallado ideal !
 ;
It`s full copy of a service manual from url http://www.philips.owner-manuals.com/PM3216-service-manual-PHILIPS.html
;
perfect! you just sent to me the copy in Italian witout even my specification!!!! so you are really smart cooperative and efficient. To my opinion the best place all over to get a manual of electronics!!!!
;
Well Well Well!!!! Good manual perfect for my hobby!!! As Before you have done a very well done work!!!! Thank you
;
Super nice! Good to have a manual in digital format.
5. Specify time-varying change in the tone
Use EG 1 to create time-varying change in the cutoff frequency (FILTER �Cutoff�). If you wish to use the front panel knobs to adjust the EG 1 parameters, use the SEQ EDIT [SELECT] key to make the SEQ 1�3 LED�s go off.
Cutoff Note on Note off
d. Adjust the speed at which the tone will change after the note is released
q Rotate the EG 1 [RELEASE] knob. The LCD screen will show Page 10D: EG 1 �Release.� Rotating the knob toward the right will make the sound change more slowly, and rotating it toward the left will make it change instantly.
10D EG1 Release:
000
c a b d
Time
6. Adjust the output of the timbre
a: Attack Time b: Decay Time
c: Sustain Level d: Release Time
a
a
b
c
d
b
a. Adjust the speed at which the tone will change during the attack
q Rotate the EG 1 [ATTACK] knob. The LCD screen will show Page 10A: EG 1 �Attack.� Rotating the knob toward the right will cause the tone to change more slowly, and rotating it toward the left will cause the tone to change instantly.
10A EG 1 Attack:
c
d
a. Adjust the volume of the timbre
000
If rotating the knob does not produce an effect, try adjusting the FILTER [EG 1 INT] knob, or make sure that the SEQ EDIT SEQ 1�3 LED�s are dark. If these LED�s are lit, it is not possible to edit the EG or LFO. The knobs will function to edit the sequence data.
q Rotate the [LEVEL] knob. The LCD screen will show Page 09A: AMP �Level.� If the volume changes over time, this level will be the maximum level that occurs during the change in volume.
09A AMP Level:
b. Adjust the speed at which the tone will change during the decay
q Rotate the EG 1 [DECAY] knob. The LCD screen will show Page 10B: EG 1 �Decay.� Rotating the knob toward the right (increasing the value) will cause a longer decay time until the sustain level is reached.
10B EG 1 Decay: 030
127
b. Adjust the output panpot (stereo position)
q Rotate the [PAN] knob. The LCD screen will show Page 09B: AMP �Panpot.� When the knob is in the center (CNT), the output will be centered.
09B AMP Panpot: CNT
c. Adjust the brightness of the sustained sound
q Rotate the EG 1 [SUSTAIN] knob. The LCD screen will show Page 10C: EG 1 �Sustain.� The change in brightness produced by the [SUSTAIN] knob will depend on the setting of the [EG 1 INT] knob.
10C EG 1 Sustain: 060
c. Select the envelope source for the volume
q Press the [EG 2 /GATE] key. Each time you press the key, the envelope source will change. If you want the volume change over time, select EG 2 ([EG 2/GATE] key LED dark). If you want the volume to sound at a �xed level, as on an organ, select GATE ([EG 2/GATE] key LED lit).
22
|
|
|
> |
|
