|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is an excellent information source. Great quality and tons of info regarding technical service for the Technics SH8065.
;
5 stars on this manual since it is the complete version, not the half manual you find free for download all over the web. Good job.
;
Thank you very much you are helping me a lot with my preferred hobby!!! this manual of an old TV is going to be very helpful!!!!
You are very honest competent great job very clear and well done!!!!
Matteo
;
An excellent service manual contains dismantling locations of components, electronic adjustments,worth the money.
;
Caracteristiques,circuit adjusment,notes on schematis diagram,it's a good service manual,to live well,thanks.
FIRMWARE RENEWAL MODE
1. Turn the power on and press [SELECT] button on the remote control unit to put the DVD player into DVD mode. Then remove the disc on the tray. (It is possible to move to F/W version up mode only when the DVD player in DVD mode with the tray opened.) 2. To put the DVD player into F/W version up mode, press [9], [8], [7], [6], and [SEARCH MODE] buttons on the remote control unit in that order. Fig. a appears on the screen.
"*******" differ depending on the models.
5. After programming is finished, the tray opens automatically. Fig. e appears on the screen and the checksum in (*3) of Fig. e.
"*******" differ depending on the models.
F/W Version Up Mode
Model No : ******* VERSION : *.**
VERSION : X5****_****.ab5 Completed SUM : 7ABC (*3)
F/W Version Up Mode
Model No : ******* VERSION : *.**
Please insert a DISC for F/W Version Up.
Fig. e Completed Program Mode Screen
6. 7.
EXIT: SELECT
Fig. a Version Up Mode Screen
8. 9.
The DVD player can also enter the version up mode with the tray open. In this case, Fig. a will be shown on the screen while the tray is open. 3. Load the disc for version up. 4. The DVD player enters the F/W version up mode automatically. Fig. c appears on the screen. If you enter the F/W for different models, �Disc Error� will appear on the screen, then the tray will open automatically.
"*******" differ depending on the models.
At this time, no buttons are available. Remove the disc on the tray. Press [CH UP/DOWN] button on the unit to go to TV mode, or press [POWER] button on the unit to turn the power off. Press [SELECT] or [DVD PLAY] button on the remote control unit to put the DVD player into DVD mode again. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. g appears on the screen.
"*******" differ depending on the models.
MODEL : ******* Version : *.** Region : *
F/W Version Up Mode
Model No : ******* VERSION : *.** VERSION : X5****_****.ab5 Reading...(*2)
EEPROM CLEAR : CLEAR
EXIT: SELECT
Fig. g
10.Press [CLEAR] button on the remote control unit. Fig. h appears on the screen.
"*******" differ depending on the models.
Fig. c Programming Mode Screen
The appearance shown in (*2) of Fig. c is described as follows:
No. 1 2 3 Appearance Reading... Erasing... State Sending files into the memory Erasing previous version data
MODEL : ******* Version : *.** Region : * EEPROM CLEAR : OK
Programming... Writing new version data
EEPROM CLEAR : CLEAR
EXIT: SELECT
Fig. h
When �OK� appears on the screen, the factory default will be set. Then the firmware renewal mode is complete. 11.To exit this mode, press [CH UP/DOWN] or [SELECT] button to go to TV mode, or press [POWER] button to turn the power off. 1-7-1 T9000TEST
|
|
|
> |
|
