PHILIPS MT1345W
Owner's Manual

SETTING UP
REMOTE

AND

USING YOUR TV (CONT�D)
SLEEP

T

o load the batteries into the remote:

Point the remote control toward the remote sensor on the TV when operating the TV with the remote. (See Television illustration below.)
SLEEP Button Press to set the TV to turn itself off automatically. Details are on page 5. Number Buttons Press to select channels. � Cable Users Enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0,6. If you only press the Number 6 button, channel 6 will be selected after a brief delay. (There also may be a brief delay when you select channels 10, 11, and 12.) If you want to select channels 100 and above, enter channel numbers as a three-digit number. For example, to select channel 117, press 1, 1, 7. � Antenna Users Enter channel numbers as a two-digit number for the quickest results. For example, to select channel 5, press 0,5. If you only press the Number 5 button, channel 5 will be selected after a brief delay. You may only select channels 2-69. STATUS/EXIT Button Press to see the current channel number on the TV screen. Press to remove the onscreen menu. You also may remove the menu by pressing the CH(annel) v/w buttons to select EXIT, then pressing the VOL(ume) B/{ buttons. (You may need to select EXIT repeatedly to completely remove all of the menus.)

POWER Button Press to turn the TV on and off.
POWER

1. Press in the tab on the battery compartment lid on the bottom of the remote control, then lift off the lid. 2. Insert two AA batteries (supplied) into the battery compartment as indicated inside the compartment. Installing batteries incorrectly may damage the remote control. 3. Replace the lid.
Battery Compartment Lid

1 4 7
STATUS/EXIT

2 5 8 0

3 6 9
ALT.CH

ALT. CH (Alternate Channel) Button Press to return to the TV channel you were viewing immediately before switching to your current channel. MENU Button Press to access or remove the on-screen menu. Press the CH(annel) v/w buttons to select an item in the menu. Press the VOL(ume) B/{ buttons to adjust an item in the menu or to advance to the next menu.

MENU

CH.

MUTE

MUTE Button Press to disable the sound on the TV. Press again to restore the sound. VOL(ume) B/{ Buttons Press to adjust the TV sound level. Press to adjust an item in the on-screen menu or to advance to the next menu. If you press the VOL(ume) { button when the sound is muted, the volume indicator will appear on the screen. Pressing the VOL(ume) B button when the sound is muted will restore the sound. CH(annel) v/w Buttons Press to scan through available channels. Details are on page 3. Press to select an item in the on-screen menu. FM Button Press to select FM radio mode. Details are on page 5. Press again to return to TV mode. CC (Closed Caption) Button Press repeatedly to select a Closed Caption mode. Details are on page 7. TV/AUX Button Press to select A/V IN (for viewing video playback at the TV from a VCR, camcorder, DVD Player, etc.). Press again to return to TV channels. Details are on page 3.

VOL. CH.

VOL.

TV/AUX

CC

FM

Battery Compartment

TELEVISION
Press the POWER button to turn ON the TV. Be sure to connect the TV power cord to a standard AC outlet first. Press the VOLUME v/w buttons to adjust the sound level. Press the CHANNEL v/w buttons to select available TV channels. (See Auto Install on page 3.) Press the MENU button to display the TV�s on-screen menu. Press the CHANNEL v/w buttons to select an item in the menu. Press the VOLUME v/w buttons to adjust an item in the menu or to advance to the next menu. Note: To remove the menu, press the CHANNEL v/w buttons to select EXIT. Then, press the VOLUME v or w button. (You may need to select EXIT repeatedly to completely remove all of the menus.) Or, press the MENU button, repeatedly if necessary, to remove the MENU.

SMART HELP
The current channel number will appear briefly when the TV is first turned on and with channel changes. To display the channel number for five seconds, press the STATUS/EXIT button on the remote control. You can turn on the TV by pressing the CHANNEL v or w button on the front of the TV. The CH(annel) v/w buttons of the remote control will not turn on the TV power.

VIDEO

AUDIO

EARPHONE MENU

VOLUME

CHANNEL

POWER

Remote Sensor Point the remote control here when using the remote to work the TV.
VIDEO AUDIO

EARPHONE MENU

VOLUME

CHANNEL

POWER

Notes: � You can connect earphones (not supplied) to the EARPHONE jack on the front of the TV for private, personal listening. � You can connect the AUDIO/VIDEO In jacks on the front of the TV to the AUDIO/VIDEO OUT jacks of a camcorder, VCR, or other video equipment. Details are on page 3.

FEATURES
CHANNEL EDIT
UTO INSTALL (see page 3) memorizes all the channels on your Antenna or Cable TV system. CHANNEL EDIT makes it easy for you to add other channels or drop unwanted channels from the TV�s memory. Then, when you use the CH(annel) o/p buttons, you will only scan through the channels you want.
1 4 7
STATUS/EXIT

A

Press the MENU button, then press the CH(annel) v or w button to select SETUP.
SmartLock SmartLock REVIEW SETUP EXIT BRIGHTNESS B B B B 24

Press the VOL(ume) B or { button to continue to the SETUP menu.
FM ANTENNA EXIT LANGUAGE AUTO INSTALL CHANNEL EDIT EXT B ENG B B

Press the VOL(ume) B or { button to continue to the CHANNEL EDIT menu. CHANNEL will be selected.
EXIT CHANNEL SKIPPED B 10 YES

Press the CH(annel) v or w button to select SKIPPED. Then, press the VOL(ume) B or { button to set
SKIPPED to YES (if you want to skip past the channel when using the CH(annel) v/w buttons) or NO (if you want the channel to be available when you are using the CH(annel) v/w buttons).
CHANNEL SKIPPED EXIT 18 NO B

2 5 8 0

3 6 9
ALT.CH

Press the CH(annel) v or w button to select CHANNEL EDIT.
LANGUAGE AUTO INSTALL CHANNEL EDIT FM ANTENNA EXIT ENG B B EXT B

While CHANNEL is selected, press the VOL(ume) B or { button or the Number buttons to select the channel you want to add or skip.
EXIT CHANNEL SKIPPED B 18 YES

MENU

MUTE

CH. VOL. CH. VOL.

_
-4-

Press the STATUS/EXIT button when you are finished.