|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It took about 24-hours after my payment before I was able to get to the download. Apparently, payment processing is not 100% automated. That is no big deal, just be aware of that going in.
After I got to it, it was in good shape, easy to read, etc. Not some cheap FAX copy looking thing.
Also, this site was the cheapest I found. Another Plus!
 ;
Good price, very legible manual, exactly what I needed -- but had to wait a day to actually get the download of the manual. Would have preferred to download it immediately after payment rather than waiting for someone to "process" my order. I was surprised that I had to wait that long.
;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
DISASSEMBLY INSTRUCTIONS
2-16: CAPSTAN DD UNIT (Refer to Fig. 2-16) 1. Remove the Capstan Belt. 2. Remove the 3 screws 1. 3. Remove the Capstan DD Unit.
Spring Position
Fig. 2-13-B
Capstan Belt Capstan DD Unit
2-14: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-14) 1. Remove the screw 1. 2. Remove the FE Head.
1
FE Head
1 1
� Screw Torque: 5 ± 0.5kgf�cm
1
Fig. 2-16
� The FE Head is not installed on the Video Cassette Player. � Screw Torque: 4 ± 0.5kgf�cm
2-17: MIDDLE GEAR/MAIN CAM (Refer to Fig. 2-17-A) Fig. 2-14 1. Remove the Polyslider Washer 1, then remove the Middle Gear. 2. Remove the E-Ring, then remove the Main Cam, P5 Cam, Pinch Roller Cam and Joint Gear.
1
Middle Gear E-Ring Main Cam
2-15: AHC ASS'Y/CYLINDER UNIT ASS'Y (Refer to Fig. 2-15) 1. Unlock the support 1 and remove the AHC Ass'y. 2. Remove the 3 screws 2. 3. Remove the Cylinder Unit Ass'y. NOTE When you install the Cylinder Unit Ass'y, tighten the screws from (1) to (3) in order while pulling the Ass'y toward the left front direction.
Pinch Roller Cam Joint Gear P5 Cam
AHC Ass'y
Cylinder Unit Ass'y
1
Fig. 2-17-A NOTE When you install the Pinch Roller Cam, P5 Cam and Main Cam, align each marker. (Refer to Fig. 2-17-B)
Pinch Roller Cam
2 (1)
(2) 2 � Screw Torque: 3 ± 0.5kgf�cm
2
(3)
Check the hole of Main Chassis can be seen.
P5 Cam
Fig. 2-15
Marker
Main Cam
Fig. 2-17-B
|
|
|
> |
|
