|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thanks for this "hard to find" service manual. This Sony PS212A is a very good turntable that needed to be restored !
 ;
Excellent quality on these manuals. Same as having the original printed manual and incredibly useful when doing a custom install like me. Keep it up on the good work.
;
This is an excellent information source. Great quality and tons of info regarding technical service for the Technics SH8065.
;
5 stars on this manual since it is the complete version, not the half manual you find free for download all over the web. Good job.
;
Thank you very much you are helping me a lot with my preferred hobby!!! this manual of an old TV is going to be very helpful!!!!
You are very honest competent great job very clear and well done!!!!
Matteo
DISASSEMBLY INSTRUCTIONS
2-10: CASSETTE OPENER/PINCH ROLLER BLOCK/P5 ARM ASS�Y (Refer to Fig. 2-10-A) 1. Unlock the support 1 and remove the Cassette Opener. 2. Remove the Pinch Roller Block and P5 Arm Ass�y.
1
Cassette Opener
Spring Position Pinch Roller Block
Fig. 2-11-B
P5 Arm Ass�y
2-12: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-12) 1. Remove the screw 1. 2. Remove the FE Head.
1
Main Chassis
Fig. 2-10-A NOTE 1. Do not touch the Pinch Roller. (Use gloves.) 2. In case of the Pinch Roller Block and the Pinch Roller Cam installation, install correctly as Fig. 2-10-B.
FE Head
Pinch Roller Block
Can be seen the hole of the Pinch Roller Cam.
P5 Arm Ass�y
� Screw Torque: 5 ± 0.5kgf�cm � The FE Head is not installed on the Video Cassette Player.
Fig. 2-12
Can be seen the hole of the Main Cam.
2-13: AHC ASS'Y/CYLINDER UNIT ASS'Y (Refer to Fig. 2-13) Fig. 2-10-B 1. Unlock the support 1 and remove the AHC Ass'y. 2. Disconnect the following connector: (CD2001) 3. Remove the 3 screws 2. 4. Remove the Cylinder Unit Ass'y. NOTE 1. When you install the Cylinder Unit Ass'y, tighten the screws from (1) to (3) in order while pulling the Ass'y toward the left front direction.
2-11: A/C HEAD (Refer to Fig. 2-11-A) 1. 2. 3. 4. Remove the screw 1. Remove the A/C Head Base. Remove the 3 screws 2. Remove the A/C Head and A/C Head Spring.
NOTE 1. Do not touch the A/C Head. (Use gloves.) 2. When you install the A/C Head Spring, install as shown in Fig. 2-11-B. 3. When you install the A/C Head, tighten the screw (1) first, then tighten the screw (2), finally tighten the screw (3).
(1) (3)
Cylinder Unit Ass'y
2 2
(2)
2 1
A/C Head
AHC Ass'y
A/C Head Spring (3)
1
(1) A/C Head Base � Screw Torque: 5 ± 0.5kgf�cm (Screw 1)
(2)
2 2
2
� Screw Torque: 3 ± 0.5kgf�cm
Fig. 2-13
Fig. 2-11-A B2-4
|
|
|
> |
|
