|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I am very grateful for this manual. Without it could not repair my receiver.
;
excellent work as always you do cheap, fast net and clean. you do an incredible service......thanks!
;
Great Job even clear than the one before!!!! god organization- I'm always very satisfied
;
I'm very happy that you all are performing an incredible good job. Furthermore what you did is very useful for all people as me that have electronics as an hobby.Thank you!!!!!
;
Manual found fast and good quality, very helpfull service
CUC 2058 D / 2059 D
Allgemeiner Teil / General Section
SETTINGS ____________________________________________________________________________________
Picture settings
Adjusting the contrast and sharpness
1 Call up the » PICTURE« menu with »z«.
� The »PICTURE« menu appears.
PICTURE
Contrast Sharpness
sssssssss� sssssssss�
___ �� ___ ��
TXT
2 Select the desired function (»Contrast« or »Sharpness«) with »,« or ,
».«. .
3 Adjust the contrast or sharpness with »F« or »E«, respectively. F E
Note: The TV set has been tested using maximum contrast, in order to check for reliability of all modules. Depending on the location of the set and the brightness in the room (surrounding light) it does however make sense to reduce the contrast slightly for the best possible picture impression. The sharpness adjustment is not needed for digital services, i.e. the row »Sharpness« is not available in digital mode.
4 End the setting with » TXT«.
Adjusting the tint for NTSC broadcasts
Note: The » Tint« row appears only with NTSC broadcasts.
PICTURE
Contrast Sharpness Tint
sssssssss� sssssssss� sssssssss�
1 Call up the » PICTURE« menu with »z«.
___ �� ___ ___ �� ��
TXT
� The »PICTURE« menu appears.
2 Select the » Tint« row with »,« or ».«. , . 3 Adjust the tint with »F« or »E«. F E
24
4 End the setting with » TXT«.
SETTINGS ____________________________________________________________________________________
Sound settings
Stereo/two-channel sound, mono
If the TV set receives two-channel sound transmissions � e.g. a film in the original language on sound channel B (display: » DUAL B «) and the synchronized version on sound channel A (display: » DUAL A «) � then you may select the desired sound channel. If the set receives stereo or NICAM transmissions, it automatically switches to stereo sound (display: »Stereo«). If stereo reception is poor, then the sound should be switched to » Mono «.
1 Call up the »SOUND« menu with » F «.
SOUND
TV Effects A 01 L/R Dolby Pro Logic Stereo Stereo
2 Select the »
A 01« (A = analogue TV channel) row with »,« or ».« , .
then select the desired sound mode with »F« or »E« . F E
y
3 If the sound for a particular channel is to be permanently in mono, select the
OK TXT
»
P..« row with »,« or ».« then press »OK«. , .
Note: To cancel this setting, repeat step 3.
4 End the setting with » TXT«.
SOUND ������������������� ��������
TV Effects A 01 L/R Stereo Dolby Pro Logic
Adjusting the bass and treble
1 Call up the »SOUND« menu with » F «.
y
Stereo
OK
TXT
3 Adjust the bass or treble with »F« or »E«, respectively. F E 4 End the setting with » TXT«.
� The setting is saved automatically.
25
1 - 15
GRUNDIG Service
ENGLISH
2 Select the desired row (»
« � bass, or » « � treble) with »,« or ».«. , .
|
|
|
> |
|
