|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
 ;
Received downlink in less then 8 hours, Item was in good copy condition, and told me how to program the clock timer. The price was very resonable, and the process was very automated and was GREAT to work with.
;
Fast service, document is OK. Thanks! Searched for it long time.
;
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! Dziękujemy za!
;
It answered my question, which was how to load the paper. I did notice that the very end of the manual was not visible.
TUNER
Tuning to radio stations
You can search for radio stations by scanning the frequency band. You can also key in the frequency of a known radio station. If an FM station is being broadcast and received in stereo, STEREO is shown. Searching for radio stations 1 Turn SOURCE SELECTOR to select the tuner. yTUNER is displayed. 2 Select a waveband by pressing TUNER BAND repeatedly. yThe selected waveband is displayed. 3 Keep 1 or 2 pressed for approximately 1 second. ySEARCH is displayed and the tuner tunes to a station with sufficient strength. 4 Repeat this procedure until you find the desired station. � To fine tune to a weak transmitter, briefly press 1 or 2 as often as necessary for optimum reception. Tuning to a radio station by frequency (with the remote control only) 1 Press TUNER. yTUNER is displayed. 2 Press FR. D.. y_ is displayed. 3 Use 1�0 to key in the frequency of a radio station. Notes: Only valid numbers within the frequency range of the tuner can be keyed in.
Storing radio stations
You may store up to 30 radio stations in the memory. The receiver can select and program radio stations by itself or you can choose them yourself. Automatic programming 1 Choose * TUNER from the menu and press NEXT 2. 2 Choose AUTO INSTALL and press NEXT 2. yThe preset number where programming will start, the waveband and AUTO are displayed. 3 Turn TUNER PRESET X to change the preset number where programming should start. 4 Use TUNER BAND to switch to the desired waveband. 5 Press ENTER / OK to start programming. yAUTO INSTALL flashes and all available radio stations are programmed, this may take a few minutes. Programming is done when AUTO INSTALL stops flashing. Manual programming 1 Choose * TUNER from the menu and press NEXT 2. 2 Choose MAN INSTALL and press NEXT 2. yA preset number, the waveband and the frequency are displayed. 3 Turn TUNER PRESET X to change to the preset number where the radio station should be stored. 4 Tune to the desired radio station (see �Searching for radio stations�). 5 Press ENTER / OK to confirm your selection. ySTORED is displayed briefly. The radio station is programmed at the chosen preset number. 6 Select and store all desired radio stations this way.
Switching FM sensitivity
You can switch the tuner to a lower search sensitivity, to search only for stations with a strong signal (FM only). 1 Turn SOURCE SELECTOR to select the tuner. yTUNER is displayed. 2 Press SENS. on the receiver. yEither SENS HI or SENS LO is displayed for 5 seconds. Note: While searching for radio stations, the actual sensitivity is displayed. In this case, SENS LO means the tuner is looking only for radio stations with a strong signal.
23
English
|
|
|
> |
|
