|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
High quality scan of the manual, very quick and easy download and very important, a truly honest price. thanks
 ;
Minden rendben, de két megjegyzés, az ábrák nehezen kivehetők és a fizetés után 24 órát kell várni a letöltésre.
;
Manual correct, and complete. Downloads cleanly. Format of manual was presumably difficult to PDF to A4, but works reasonably well.
;
This was a hard to find manual. When I did find it , some sites wanted way too much for the file.
Owner-manual .com had it for a really reasonable price. Not only that but it was sent very quickly and was a quality scanned document, unlike some others I purchased from a different site.
Good job guys!!
Larry
;
Fast and courteous service. Product delivered as described. Thank you.
Using the Tuner
2
Select a station using one of the following methods.
� Manual Tuning Briefly press the 22 or ¡ button on the Unit to move from frequency to frequency until you find the station you want. OR � Auto Tuning If you hold down the 22 or ¡ button on the Unit for 1 second or more and then release it, the frequency changes down, or up, automatically until a station is found. OR � Preset Tuning (Possible only after presetting stations) Preset tuning using the Unit: Select the preset number you want, using the 4 or ¢ button.
Using the Unit
1 2 3 4
Select a band by pressing the FM/AM button. Press the or station. Press the SET button. Press the 4 or preset number.
¢: 4:
22
¡
button to tune in a
�SET� will blink for 10 seconds.
¢ button
to select the
Increases the preset number by 1. Decreases the preset number by 1.
5 6
Press the SET button.
�STORED� appears and, after 2 seconds, the display returns to the band/frequency display.
Example:
Press the ¢ button until the preset number �P-12� appears on the display. After 2 seconds, the display will show the preset number�s band and frequency.
PRESET
Repeat above steps 1 to 5 for each station you want to store in memory with a preset number.
To change the preset stations, repeat the same steps as above.
or
(After 2 seconds)
kHz MHz
Preset tuning using the Remote Control: Enter the preset number you want to recall using the numeric keys. See �Entering the Number with the Remote Control� on page 8.
� In step 4, you can select the preset number using the numeric keys on the Remote Control. See �Entering the Number with the Remote Control� on page 8.
CAUTION:
� Even if the System is unplugged or if the power failure occurs, the preset stations will be stored for a few days. However, in case the preset stations are erased, you will need to preset the stations again.
Example:
Press +10, then 2 to recall the preset number 12. After 2 seconds, the display will show the preset number�s band and frequency.
� In AM broadcast, reception sensitivity will be changed by turning the AM loop antenna. Turn the AM loop antenna for best reception.
To Change the FM Reception Mode
When you are tuned in to an FM stereo broadcast, the �ST (Stereo)� indicator lights up and you can hear stereo effects. If an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Reception improves, but you lose stereo effect. Press the FM MODE button on the Remote Control so that the �MONO� indicator lights up on the display.
FM MODE
Presetting Stations
You can preset up to 30 FM stations and up to 15 AM stations.
� Preset numbers may have been set to factory test frequencies prior to shipment. This is not a malfunction. You can preset the stations you want into memory by following one of the presetting methods below. � During presetting stations, if no button operation is made for 10 seconds, the display returns to the band/frequency display. In this case, repeat steps from the beginning.
ST
MONO
To restore the stereo effect, press the FM MODE button on the Remote Control so that the �MONO� indicator goes off.
FM / AM
TUNING
SET
or
SET
FM=30, AM=15
When changing the Band
10
English
|
|
|
> |
|
