|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a high quality manual with clear schematic and components layout diagrams ; with service procedure included.
 ;
This service manual for the Kenwood KT-990D was reproduced really well ,is very legible and manual is complete.Combined with the low price paid,in the future,I will be checking Owner-Manuals.com any time I need a manual.
;
When I purchased this manual I had my doubts regarding the quality as the price was so reasonable as compared to other outlets.
The manual itself is of high standard the print is very clear as are the diagrams. Obviously with the diagrams one has to zoom in otherwise it is to small to be able to read.
Overall I am very pleased with the company who delivered as they said and with the manual they supplied.
I occasionally require a manual and now having registered with this company I shall order from them in the future.
;
I was at first dubious about payiong for downloaded manuals but having done so, I was extremely impressed with quality of the two manual I ordered, well worth the small price I paid.
I would highly recommend these to my friends.
;
reasonable price for the schematic - the service is perfect, all as expected and pointed by instructions - good scan of the original plans - thank you!
SECTION 3 TEST MODE
General � In the TEST mode, this set provides the Auto mode in which both CD and MO are adjusted automatically. In the Auto mode, whether a disc is CD or MO is discriminated, then each adjsutment is automatically executed sequentially. If a fault is found, it is displayed. Also, in the Servo mode, each item can be adjusted automatically. Entering TEST Mode To enter the TEST mode, the following two methods are available: Method-1. Entry by key input Turn on the HOLD switch on the main set, and while pressing p key on the main set, press the following keys on the remote controller in this order. + �+ �= �= �+ �= �+ �= � P�P Method-2. Entry by shorting the test point Bridge the TAP801 (TEST) with a solder (connect IC801 #� to GND) on the MAIN board, turn on the POWER switch, and press ( key. Releasing TEST Mode 1. Turn off the POWER switch. 2. Remove the solder bridge form TAP801 (TEST) on the MAIN board. (This is required only when using Method-2.) Operation in TEST Mode In the TEST mode, the Remote controller LCD display is as shown below: Configuration of TEST Mode The TEST mode configuration of this set is as follows:
+key
pkey
AUTO Mode (key Auto?
pkey
Start?
pkey
Display in TEST Mode
�key
pkey
MANUAL Mode Manu?
(key
SERVO Mode
000
+,�key AUDIO Mode
100
+,�key POWER Mode
300
SERVO Mode � Enter the TEST mode, press VOL � key and ( key to select the SERVO mode. � When the second digit of mode number is not 0 and the first digit is 0 (010, 020, 030, etc.), the optical pickup moves to outside track or inside track with + key or = key respectively. � To select other modes, refer to the TEST mode configuration. 1. Configuration of SERVO Mode
+,�key
300
V3.000
Remote controller LCD
ROM version display
SERVO Mode
000
(key
� ROM version display � All ON � All OFF are repeated. � To hold the display for confirmation, press the PLAY MODE key.
pkey
OFFSET Adj.
(key
010
Each time (key is pressed, 011-013 modes pkey are switched. (For each mode, see relevant table)
(key
pkey
LASER POWER Adj.
(key
020
Each time (key is pressed, 021-024 modes pkey are switched. (For each mode, see relevant table)
(key pkey
MO Adj.
(key
030
Each time (key is pressed, 031-039 modes pkey are switched. (For each mode, see relevant table)
(key
1
2
(To page 10 )
3
�9�
+,�key
 $4.99 MZE25 SONY
Owner's Manual Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
|
|
|
> |
|
