|
Who's Online
There currently are 5924 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
It is wonderful done!!! a great job in scanning the manual. Superior quality in all the electric scheme. Very understandable and net!!! Thank you!
;
muy buen manual por lo completo de este algunos esquemas estan muy divididos lo que hace algo dificil el seguimiento.
;
very good manual, with detail and clarity in esquematic diagrams and waveforms .
;
Very quality copy of original service manual, which contains the circuit diagrams, PCB and lists of components, well as recommendation for calibration procedures of device, also everything else, that need for repair, tuning and use this oscilloscope.
All presented copies have high-resolution, so you can view all in detail.
This manual will very useful for simple owners and for repairers.
I recommend these manual, because myself is owner of Philips PM3216 and I need sometimes servicing these oscilloscope (principally calibrating).
Also, these document is an example of excellent design of technical documentation.
;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
MZ-N10 SECTION 4 TEST MODE
Outline
� This set provides the Overall adjustment mode that allows CD and MO discs to be automatically adjusted when in the test mode. In this overall adjustment mode, the disc is discriminate between CD and MO, and each adjustment is automatically executed in order. If a fault is found, the system displays its location. Also, the manual mode allows each individual adjustment to be automatically adjusted. � Operation in the test mode is performed with the set. A key having no particular description in the text, indicates a set key. � For the LCD display, the LCD on the remote commander is shown, but the contents of LCD display on the set are same. (Both displays may be displayed.) 3 In case of setting the test mode by keys on the set and remote commander: In the normal mode, turn on the [HOLD] switch on the set. While pressing the x key on the set, press the keys on the remote commander with the following order: >t>t.t.t>t .t>t.t t
Note: If electrical adjustment (CD and MO overall adjustment) has not been finished completely, �ERROR� is displayed on LCDs of the set and the remote commander.
Operation in Setting the Test Mode
� When the test mode becomes active, first the display check mode is selected. � Other mode can be selected from the display check mode. � When the test mode is set, the LCD repeats the following display.
Setting Method of Test Mode
There are three different methods to set the test mode: 1 Short SL803 (TEST) on the MAIN board with a solder bridge (connect pin <zx. of IC801 to the ground) and turn on the power.
� MAIN Board (Side B) �
Remote commander LCD display
All lit
All off
Microcomputer version display
V1.100
Set LCD display
All lit
IC801
All off
TP1829
1-686-347-
Microcomputer version display
001
R838
C815
Ver 1.100
SL803 (TEST)
2 In case of setting the test mode only by keys on the set: In the normal mode, turn on the [HOLD] switch. While pressing the [GROUP] key press the following order: >t>t.t.t>t .t>t.tXtX
� When the X key is pressed and hold down, the display at that time is held so that display can be checked.
Releasing the Test Mode
For test mode set with the method 1: Turn off the power and open the solder bridge on SL803 (TEST) on the MAIN board.
Note: Remove the solders completely. Remaining could be shorted with the chassis, etc.
For test mode set with the method 2 or 3: Turn off the power.
11
$4.99 MZ-N10 SONY Owner's Manual Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
|
|
|
> |
|