|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Probably it never existed a 1081 official service manual from Commodore, it's look more like a NAPCEC service manual & diagrams compilation of the 1084 series and his variants, like the nap6523, 8cm505, 1084S, 1084P and obviously the 1081. It's more complete than other scans and the quality of the scans also are far superior. It has two circuit diagrams variants of the 1081, mono and stereo versions. It doesn't include a diagram for the Philips CM8500 or CM8501, they look like the 1081 but they are slightly different.
 ;
Rapid, clear well done as all the scheme I downloaded from this site. Great job very functional and very useful
;
Great copy of the manual, has all information required for servicing,
;
I work at an authorized service center and I can tell if a manual is as it should be. This one is. It may be a scan, but a very good one at that. The interesting part for me was the curcuit diagram which was scanned at high quality, making it as good as the original. I will definitely be back as a customer. I need not say this, but I will: the price was the best. Thank you owner-manuals.com .
;
really a very good manual even sometimes the quality is no so good as before still very readible and very very useful!
MZ-NF810/NF810CK
Power Supply Adjustment Auto Item Feed
Note: This mode is available to perform the temperature correction and power supply adjustment without entering the manual mode.
� Setting method of power supply adjustment auto item feed mode. 1. Set the test mode (see page 13) 2. Press the . key or press the [VOL --] key to activate the T overall adjustment mode.
Remote commander LCD display
5. Connect digital voltmeter to the measuring points on the MAIN board, and adjust the voltage with the [VOL +] or [VOL --] key. (see page 18 to 21) Press the X key to write the adjusted value, and the item number increases automatically. 6. When not writing the adjusted value, press the > key to t move to the next item. The . key is available to back to the T last item. 7. The following message is displayed after all power supply adjustments finish.
Remote commander LCD display
000 A s s y
**: Adjusted value
**
000 A D J
OK
3. Press the [END SEARCH] key or [P MODE] key on the remote commander to set the temperature correction mode.
Remote commander LCD display
8. Press the xCANCEL/CHG key to return the test mode (display check mode).
015 S e t T m p * *
4. To change the initial value (hexadecimal) adjust with the [VOL +] or [VOL --] key. Press the X key to write the adjusted value, and the item number increases automatically. When not writing the adjusted value, press the > key to t move to the next item.
Remote commander LCD display
741 V C 1 L * *
� Configuration of power supply adjustment auto item feed
000Assy ** END SEARCH key or P MODE key on the remote commander. 015 SetTmp 19
> . .
749 REG3 H **
key
>
key
key
.
751 VREC L **
key
>
key
741 VC1 L **
> .
key
key
.
752 VREC M **
key
>
key
742 VC1 H **
> .
key
key
.
753 VREC H **
key
>
key
743 VC2 Lo **
> .
key
key
.
755 ChgV L **
key
>
key
744 VC2 Hi **
> .
key
key
.
756 ChgV H **
key
>
key
745 REG1 **
> .
key
key
.
757 CIL **
key
>
key
747 REG3L1 **
> .
key
key
758 CIH **
>
key
748 REG3L2 **
>
key
key
000 ADJ OK
23
|
|
|
> |
|
