|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
At first I thought there had been a mix up as I required the service manual for the cassette unit and the one supplied was for the CD unit. However when I scrolled further down I realised that both had been scanned together! This enabled me to dismantle and repair the cassette unit as intended and I also have a copy of the manual for both the CD and graphic equaliser units should I ever need them. Thanks very much for a great service.
;
Excelent service, the manual is complete, very cheap and fast
Alberto
;
The item received was as described, as expected. I was pleased with the order. Thank you.
 ;
Superb rendition. Drawings (schematics) complete and unabridged. I do a great deal of vintage audio restoration. Documentation is essential for successful repairs. I have found sources over the years that offer good documentation, but rarely all that is necessary. Owner's Manuals has filled that void with complete and legible documentation. They have narrowed my "favorites" to a more manageable collection. This Denon manual in particular contained the latest revisions level, and offered alterations favorable to updating the item. The Illustrated Parts Breakdown (IPB) was well enough detailed to simplify part symbols and physical locations. You will not be disappointed!
;
Clear and concise. Saved me a lot of time and money.
14. Head Switching Position Adjustment
Purpose: Determine the Head Switching Position during Playback. Symptom of Misadjustment: May cause Head Switching Noise or Vertical Jitter in the picture. Note: Unit reads Head Switching Position automatically and displays it on the screen (Upper Left Corner). 1. Playback test tape (VFMS0001H6). 2. Enter the Service mode in TV mode. 3. Press [5] button on the service remote control unit. 4. The Head Switching position will display on the screen; if adjustment is necessary follow step 4. 6.5H(412.7µs) is preferable. 5. Press [CH. o / p] buttons on the service remote control unit if necessary. The value will be changed in 0.5H steps up or down. Adjustable range is up to 9.5H. If the value is beyond adjustable range, the display will change as: Lower out of range: 0.0H Upper out of range: -.-H
The following 2 adjustments normally are not attempted in the field. They should be done only when replacing the CRT then adjust as a preparation.
15. Purity Adjustment
Purpose: To obtain pure color. Symptom of Misadjustment: If Color Purity Adjustment is incorrect, large areas of color may not be properly displayed. Test Point --Tape --Adj. Point Deflection Yoke Purity Magnet M. EQ. Pattern Generator Figure Mode --Input *Red Color Spec. See below
GREEN
RED
BLUE
Fig. 5 * This becomes RED COLOR if the [7] button is pressed while in service mode. 1. Set the unit facing east. 2. Operate the unit for over 30 minutes before adjusting. 3. Fully degauss the unit using an external degaussing coil. 4. Set the unit to the AUX mode which is located before CH2 then input a red raster from video in. 5. Loosen the screw on the Deflection Yoke Clamper and pull the Deflection Yoke back away from the screen. (See Fig. 6.) 6. Loosen the Ring Lock and adjust the Purity Magnets so that a red field is obtained at the center of the screen. Tighten Ring Lock. (See Fig. 5, 6.) 7. Slowly push the Deflection Yoke toward the bell of the CRT and set it where a uniform red field is obtained. 8. Tighten the clamp screw on the Deflection Yoke.
1-7-7
P77B0EA
|
|
|
> |
|
|
Parse Time: 0.442 - Number of Queries: 127 - Query Time: 0.144
