|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
My first manual from Owner-Manuals.com but not the last! I am very satisfied with the easy ordering and promt delivery of a manual I did not find anywhere else.
 ;
This manual is very helpfull to use the Power Supply. All technical information has been available.
For service use the circuit diagrams are very good.
Thanks .
;
Very comprehensive document which is a must-have for any Satellit 2100 owner whose set up is somewhat intricate. Due to the bad quality of the pictures that are rather dark and a bit blurred I gave 4-star feedback.
;
The manual was missing 2 pages but when I presented the problem to the company they made every attempt to get the 2 pages to me, when they couldn't they refunded my money. A very pleasing and easy transaction. The manual they provided was the original, it was concise and to the point. I plan to do business with this company again when should the need arise.
;
The owners manual is very good. all my how to questions were answered in detail.
0. Built-in Talkback Mic
This is where the built-in talkback microphone is located. This is an omni-directional dynamic microphone, so it will pick up your voice from anywhere in front of the unit. In addition, the talkback signal is routed through a compressor, which allows the talkback signal to maintain a constant volume regardless of how far you are from the Onyx Satellite (within reason).
mentary switch and is only active as long as you hold the button down. This allows you to slate takes as you record to the DAW. Note: When you press either of the Talkback switches, the control room outputs are attenuated momentarily so the engineer can hear himself or herself talk.
Owner�s Manual
4. CONTROL ROOM LEVEL Control
Use this knob to adjust the signal level at the CR OUT [36] jacks on the rear panel. It adjusts the signal for both the left and right Control Room A/B outputs, ranging from off (�) to maximum gain (MAX).
1. TALKBACK LEVEL Control
Use this knob to adjust the level of the talkback signal. You should start with the TALKBACK LEVEL control turned down, and then slowly turn it up until you get confirmation from whoever is listening to the headphones that they can hear you. Once you have set the level, you can leave it there for the duration of the session. If you are using the talkback mic to slate takes in your DAW, use the meters in your DAW to adjust the TALKBACK LEVEL control.
5. SOURCE Select Switch
Use this switch to select the signal source for the control room outputs. When the switch is up (DAW), the Core Audio/ASIO streams 1 and 2 from the DAW application are routed to the control room outputs. Use this to monitor tracks already recorded and to overdub additional tracks.
. TO PHONES Switch
Press this button to route the talkback signal to both PHONES outputs on the pod. This is a momentary switch and is only active as long as you hold the button down. This allows you to talk to the talent without them having to remove their headphones.
When the switch is down (INPUTS), channels 1 and 2 from the Onyx Satellite are routed to the control room outputs. This allows you to listen to whatever is connected to the Onyx Satellite without having a computer connected. Maybe you have a CD player or iPod connected to the Onyx Satellite and you want to listen to it through your control room monitor speakers. Voila! This is particularly useful when you have a home studio setup that does double-duty as a home stereo system.
. TO DAW Switch
Press this button to route the talkback signal to channels 1 and 2 being fed to the DAW. This is a mo-
1
MIC 1 2 MIC 1 2
2
TO PHONES
TALKBACK
TO DAW DAW INPUTS
CONTROL ROOM
A B 1-2 1-6
ON
O O
LEVEL
MAX
SOURCE
O O
LEVEL
MAX
Owner�s Manual
1
|
|
|
> |
|
