SONY P700
Service Manual

Customizing Your Monitor
Customizing Your Monitor Degaussing the monitor 4 Adjusting quality of the
Select To power is turned on.

To manually degauss monitor, first press the v/V buttons to highlight (MANUAL DEGAUSS). the picture by eliminating red or blue shadows around letters, The monitor is degaussed for about three seconds. If a second of the picture (SIZE/CENTER) Both settings are stored in memory for all input signals.
screen The main MENU appears on the screen. rotate picture The CONVERGENCE settings allow you to adjust the quality of ROTATION

Adjusting the Settings

The monitor is automatically degaussed (demagnetized) when the picture (CONVERGENCE)

1 Adjusting the size and centering PINCUSHION expand or contract picture sides Then press only the right 6 b button. characters and lines.
minutes for best result. KEYSTONE adjust picture width at top of the 1

PIN shift picture sides to the left or right BALANCE degauss cycle is needed, allow a minimum interval of 20

This setting is stored in memory for current input signal. Press the MENU button.

1 Press MENU button. shift picture to left or right at the KEY BALANCE
To adjust the amount of moire cancellation, first press CONVERGENCE and press the MENU button again. the v/V buttons to highlight ( MOIRE

Adjusting amount of the moire cancellation 2 The main MENU appears on screen. top of screen Press the v/V buttons to highlight
amount of cancellation until the moire effect is CENTER and press the MENU button again.

2 Press v/V buttons to highlight SIZE/ The CONVERGENCE menu appears on the screen. CANCEL). Then press 6 B/b buttons to adjust the 3 Adjusting color of the picture

(COLOR) at a minimum. The SIZE/CENTER menu appears on screen. 3 Press 6 B/b buttons to adjust the horizontal
The COLOR settings allow you to adjust the picture�s color 3 Press v/V buttons to select the desired vertical convergence. Colors appear reddish temperature is low, and bluish if the adjust setting. close OSD, press the MENU button again. temperature high. This adjustment is useful for matching the The OSD automatically disappears after about 30 seconds. To Example of moire monitor�s colors to a printed picture�s colors. close OSD, press the MENU button again. This setting is stored in memory for all input signals.

convergence, or v/V buttons to adjust the * Moire is a type of natural interference which produces soft, wavy lines on

your screen. It may appear due to interference between pattern of the

adjustment item. Then press the 6 B/b buttons to temperature by changing level of the white color field. The OSD automatically disappears after about 30 seconds. To picture on screen and phosphor pitch pattern of the monitor.

5 Changing the OSD language
1 Press the MENU button. 2 Press the v/V buttons to highlight COLOR and US shift picture up or down 1 Press MENU button. Adjusting the OSD Horizontal Position
The main MENU appears on the screen. To change horizontal position of the OSD, first POSITION). Then press the 6 B/b buttons to adjust
height The LANGUAGE menu appears on the screen. width and height enlarge Press the v/V buttons to select a color or reduce picture and press the MENU button again.

(LANGUAGE) Select To

HORIZONTAL CENTERING shift picture to left or The main MENU appears on the screen. This setting is stored in memory for the current input signal.

right

press the MENU button again.

VERTICAL CENTERING

press the v/V buttons to highlight (OSD H

enlarge or reduce picture The COLOR menu appears on the screen. HORIZONTAL SIZING width 2 Press the v/V buttons to highlight LANGUAGE

temperature.

VERTICAL horizontal position of the OSD. SIZING

3
OPTION The preset color temperatures are 9300K and 5000K. Since the

�7�
prefer. The OSD automatically disappears after about 30 seconds. To 26 step 2 above, and using 6 B/b buttons to adjust the color close OSD, press the MENU button again.
COLOR 9300K 5000K

3 Press v/V buttons to select the language you OSD H

enlarge or reduce the picture ZOOM default setting is 9300K, the whites change from a bluish hue to a reddish hue as the temperature is lowered to 5000K. POSITION proportionally You can also fine tune the color temperature by selecting in

Note temperature manually. Adjustment stops when either the horizontal or vertical size reaches its

Adjusting the OSD Vertical Position maximum or minimum value. 6 Additional settings (OPTION)
To change vertical position of the OSD, first press POSITION). Then press 6 B/b buttons to 26 moire, horizontal position, adjust the OSD vertical
OPTION

You can manually degauss (demagnetize) screen, cancel the v/V buttons to highlight (OSD V 2 Adjusting shape of the

picture (GEOMETRY) and lock controls using OPTION vertical position of the OSD.
This OSD allows you to adjust the color temperature between
POSITION 9300K and 5000K.

Press the MENU button. 1 The main MENU appears on the screen.
shape OSD V of the picture. The rotation setting is stored in memory for all input signals. All Press 6 B/b buttons to adjust the color temperature. other settings are stored in memory for the current input signal. 26

The GEOMETRY settings allow you to adjust the rotation and

2 Press the v/V buttons to highlight OPTION and

The OSD automatically disappears after about 30 seconds. To

1 Press the MENU button. The OPTION menu appears on the screen.

press the MENU button again. close OSD, press the MENU button again.

Locking the controls The main MENU appears on the screen.
To protect adjustment data by locking the controls, 3 Press v/V buttons to highlight the desired Adjust selected item according to the following instructions. The OSD automatically disappears after about 30 seconds. To

2 Press the GEOMETRY first press v/V buttons to highlight adjustment item.

and MENU button again. (CONTROL LOCK). Then press the 6 B/b buttons to The GEOMETRY menu appears screen. toggle the Control Lock on or off.

3 First press v/V buttons to select the desired

Only the 1 (power) switch and MENU button will operate. close OSD, press the MENU button again.

adjustment item. Then press the 6 B/b buttons to adjust the setting. The OSD automatically disappears after about 30 seconds. To close OSD, press the MENU button again.

7

8

P700