|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
First class Service,
best quality, come again
Thank You.
vac
;
I didn't realise a manual for an early plasma TV such as the one we were gifted could be so easily obtained. No manual was supplied with it, and as senior citizens we were a little puzzled over some aspects of its use. I do not want a listing for your store credit as we are not fairly big computer users. The manual was well organised, as it should be, with its backing of the Pioneer name. The download was prompt and everything worked quite smoothly. Thank you. Gordon.
;
Thank you very much for the manual. It is what I needed and it will be very helpful to me. The delivery of the manual was easy and very fast. I strongly recommend this site to other users. Best regards.
 ;
Excellent!! Got what I need and very fast!! Thank You
;
Manual acquired with good resolution, complete in all its pages, very good policy of the folder where are saved all products purchased.
CHAPTER 11 TROUBLESHOOTING
VII. SELF DIAGNOSIS
The microprocessor on the machine�s DC controller PCB is equipped with a self diagnostic mechanism that checks the condition of the machine (particularly, sensors) and indicates an error code in the count/ratio indicator on the control panel upon detection of a fault. In the case of �E001�, �E0� and �01� are flashed alternately.
Code Cause �E000�, �E001�, �E002�, or �E003� has occurred. � � � � � The thermistor (TH1) is faulty. The fixing heater (H1) is faulty. The thermal fuse (FU2) has blown. The DC controller PCB is faulty. The composite power supply PCB is faulty. Description The power switch is turned off and then on immediately after an error (�E000�, �E001�, �E002�, �E003�) has occurred. � The temperature detected by the thermistor (TH1) does not reach 65°C 1.5 sec after the Copy Start key has been pressed. � The temperature detected by the thermistor (TH1) does not reach 150°C 4 sec after the Copy Start key has been pressed. � The temperature detected by the thermistor (TH1) exceeds 230°C. � The temperature detected by the thermistor (TH1) exceeds by 30°C or more. � The temperature detected by the thermistor (TH1) registers an increase of 100°C or more within 1 sec. � The temperature detected by the thermistor (TH1) registers an increase of 40°C or more after it has reached 100°C during standby. � E0 detection signal (E0_DT) is detected twice or more in succession. � The temperature detected by the thermistor (TH1) has exeeded 150°C during copy operation and maximum power is applied for 10 to 14 sec thereafter. � The temperature detected by the thermistor (TH1) drops to and remains 150°C or lower after it has reached 160°C.
� The thermistor (TH1) is faulty. � The DC controller PCB is faulty. � The composite power supply PCB is faulty.
� � � � � � � � � �
The thermistor (TH1) is faulty. The fixing heater (H1) is faulty. The thermal fuse (FU2) has blown. The DC controller PCB is faulty. The composite power supply PCB is faulty. The thermistor (TH1) is faulty. The fixing heater (H1) is faulty. The thermal fuse (FU2) has blown. The DC controller PCB is faulty. The composite power supply PCB is faulty.
11-86
COPYRIGHT © 1999 CANON INC.
CANON PC800s/900s REV.0 AUG. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)
 $4.99 PC980 CANON
Parts Catalog Parts Catalog only. It's available in PDF format. Useful, if Your equipment is broken and You need t…
|
|
|
> |
|
