|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent service manual, the only known point of note is the alignment of improvability scanned pages within the pdf page. The resolution is good.
;
I was very glad recieving the service manal from You. Additionaly very fast. Extremaly nice servicing. Thanks very mach! Now my GX-220 working better, than it was made. Alexander from Moscow, Russia/
;
Sweet! I won the item on eBay and couldn't adjust the geometry or even keep a steady picure. This guide has the full schematics (not available anywhere else as far as I could tell), and was a bargain for the wealth of knowledge it contains. I hooked it up to my testing equipment, tweaked a few potentiometers and got it playing videogames in no time. Thanks!
;
It was just what I need to fix my old BMW's CD player. Very convenient also. Thank you.
;
Great Manual! It contains all the wiring schematics and mechanical exploded views that are essential for service and repair. I was surprised I even found this for such an old machine. Only wish I knew of this site many years ago.
PD-42DXT
DISPLAY INTERFACE PWB H
(x4)
E
(x6)
FILTER SHIELD
2.4.9 REMOVING THE PDP UNIT (Fig.5) � Remove the REAR COVER. � Remove the TERMINAL COVER. � Remove the CHASSIS BASE (with each PWB affixed on the CHASSIS BASE). (1) Remove the 4 screws [M], and remove the terminal bracket. (2) Disconnect the connectors of the following PWB. NOTE: � Disconnect the connector [CN0PW] from the LINE FILTER PWB. � Disconnect the connectors [CN0AU] and [CN0AT] from the PDP POWER PWB. � Disconnect the connector [CN0AH] and earth wire from the DISPLAY INTERFACE PWB. � It is advisable to take note of the connecting location (connector number) of the removed connectors. Remove the 4 screws [N] and 5 screws [O], and remove the 2 pieces of SUPPORT BRACKET (BOTTOM). Remove the 4 screws [P] and remove the 2 pieces of BACK FRAME (BOTTOM). Remove the 4 screws [Q] and 1 screw [R], and remove the 2 pieces of SUPPORT BRACKET (UPPER). Remove the 2 screws [S] and 1 screw [T], and remove the
PDP POWER PWB I
(x6)
F
(x4)
AUDIO PWB LINE FILTER PWB SYSTEM POWER PWB G
(x4)
(3) (4) (5)
INSULATOR SHEET
(6) Fig.3
2.4.8 REMOVING THE CHASSIS BASE (Fig.4) � Remove the REAR COVER. � � � � � � Remove the TERMINAL COVER. Remove the FILTER SHIELD and LINE FILTER PWB. Remove the AUDIO PWB. Remove the SYSTEM POWER PWB. Remove the DISPLAY INTERFACE PWB. Remove the PDP POWER PWB. (1) Remove the 2 screws [J] and 1 screw [K]. (2) Lift upwards and withdraw the AC inlet in a front direction. (3) Remove the 4 screws [L], and remove the CHASSIS BASE.
panel shield. (7) Remove the 4 screws [U]. (8) Life the PDP upright and remove it with enough care not to impose shock to the PDP. Caution: � Two or more people are required to remove the PDP unit � The gas pouring port is covered with the protection material.In operation, be careful not to damage the gas pouring port. � Do not touch the front side (glass) of the PDP with your fingers.
CHASSIS BASE
L
(x4)
K
J
(x2)
AC INLET COVER
Fig.4
(No.52108)1-11
 $4.99 PD-42DXT JVC
Parts Catalog Parts Catalog only. It's available in PDF format. Useful, if Your equipment is broken and You need t…
|
|
|
> |
|
