|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
;
The owners manual for the Pioneer VSX-D603S was exactly what I needed. I received it in a timely manor and it was priced fairly. I definately will use your servise again. Thank You
;
This is a great manual. It was easy to read and very accurate. The size of the manual is small so email is no problem. I highly recommend it. The manual is very hard to find other than this website.
;
Manual was complete and available promptly, since I had lost my original manual. Very good response.
TO PLAY ONLY DESIRED TRACKS/DISCS
Direct Program:
During normal playback or Magazine Hi-Lite Scan playback, the track being played can be programmed.
To erase a program (PD-M427 only) :
During program mode, press the CLEAR button on the remote control unit. The last program step is erased and the contents of the previous program step are displayed.
1. Press the PROGRAM button to enter the program mode. 2. To search for a desired track during normal play back, it is possible to skip to succeeding tracks by pressing the 4 1 or ¡ ¢ button.
Also, Magazine Hi-Lite Scan function can be used to move from track to track through the disc.
NOTE: Contents of a program can be erased during playback as well. However tracks preceding the currently playing track cannot be erased in this way.
3. If you wish to program the track currently playing, press the PROGRAM button while the track is playing.
÷ Direct programming is not possible during program playback.
To clear all of the program contents:
A. During stop mode, press the 7 button. B. When the magazine is ejected, the program contents will be cleared.
To check the program contents (PD-M427 only) :
During program mode, set the player to stop mode and press the CHECK button on the remote control unit. The program contents will be displayed in the programmed order. ÷ After confirming the last program step, the display will show �0-00�.
To modify the program contents (PD-M427 only) : 1. During program mode, set the player to stop mode and press the CHECK button on the remote control unit so that the program step to be corrected appears on the display. 2. Enter the new disc number with the DISC NUMBER (DISC 1-DISC 6) buttons and then press the 4 1 or ¡ ¢ button so that the new track number appears on the display. 3. Press the PROGRAM button.
÷ Repeat steps 1 through 3 to change other tracks as desired. ÷ If the 4 1 or ¡ ¢ button is not pressed within 2 seconds when correcting the track number, the displayed track number is automatically memorized.
PROGRAMMING A PAUSE (PD-M427 only)
Inserting a pause in your program can be very useful when carrying out recording. Press the 8 button on the remote control unit instead of entering a track number. �PA� appears on the display panel. ÷ For example, when recording on both sides of a cassette tape, if you program a pause after the last track to be recorded on the first side, program playback will pause at that point to allow you to switch tape sides. To resume program playback after the player enters pause mode, press the 8 button on the remote control unit or 6 button on the front panel.
NOTES: ÷ A pause can be programmed only when the program procedure is performed under stop mode. ÷ A pause cannot be programmed at the beginning of a program (P�01), nor can two pauses be programmed one after the other ÷ A pause inserted in a program is counted as one step. ÷ If a pause is programmed as the last step of a program, the player will not enter the pause mode.
12
En
|
|
|
> |
|
