|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Très-très bon site, facile, très bon prix.
Au futur besoin, je n’hésiterais à faire appel à vous.
Merci
;
This is the correct service manual of SHARP RX-100H(BK) DAT.
;
The ervice manual for my 1982 Kenwood KR-1000 receiver is great! Full detail on all circuits with part number detail. I will definately be ordering more manuals for my other vintage equipment! Order was fulfilled quickly! Very efficient ordering process! Thnaks for your help! Great site!
 ;
Everything in the manual was excellent except for a couple of pictures of specific areas in the unit that were a little dark. Owners Manuals re-sent the pdf file & the problem was corrected. Excellent product! George
;
Thanks for offering this item at such a good price. Proved handy in identifying the part I was looking for my set.
Thanks again.
1
2
3
4
A
8. ETC.
1 1 5 10 15 20 25 30 32
P AN E L
FAC T .
I N 1 � 5 0 6 0 2 � RGB � EHS 6 [ TBL 1 / 6 0 VS ]
7 Key operation
<DOWN> <UP> <SEL> <SET> : Shifting to MASK SETUP (+) : Shifting to PANEL REVISE (+) : MASK ON/OFF : Shifting to the next nested layer
5
10
B
15 16
E TC .
(+)
1 1
5
10
15
20
25
30
32
7 Key operation
<DOWN> : Shifting to the next item <UP> : Shifting to the previous item <RIGHT> : Adding by one to the adjustment value <LEFT> : Subtracting by one from the adjustment value <SET> : Determining the setting value and shifting to the upper layer <SEL> : MASK ON/OFF
P AN E L E TC .
FAC T .
I N 1 � 5 0 6 0 2 � RGB � EHS 6 [ TBL 1 / 6 0 VS ]
5
C
10
15 16
B AC K U P
E E P R OM
<=>
: NO
OPRT
D
<Lower-layer items of ETC.> No. Items Adjustment/Setting Value Remarks
"ERR" is indicated when no data are in the backup EEPROM. To activate the option to select TRANSFER, press the SET key about 5 seconds. (There is a situation resting more than 5 seconds.)
1
BACKUP DATA <=>
<=>NO OPRT<=>TRANSFER<=>
2
E
DIGITAL EEPROM <=> <=>NO OPRT<=>REPAIR/DELETE<=>
"DELETE" is indicated when the main unit has been already adjusted. To activate the option to select REPAIR/DELETE, press the SET key about 5 seconds. (There is a situation resting more than 5 seconds.)
3 4 5 6 7
PD INFO. <=> SD INFO. <=> HR-MTR INFO. <=> PM/B1-B5 <=> P-COUNT INFO. <=>
<=>NO OPRT<=>CLEAR<=> <=>NO OPRT<=>CLEAR<=> <=>NO OPRT<=>CLEAR<=> <=>NO OPRT<=>CLEAR<=> <=>NO OPRT<=>CLEAR<=> To activate the option to select CLEAR, repeatedly press the SET key about 5 seconds. (There is a situation resting more than 5 seconds.)
F
� "NO OPRT" is selected when this submode is entered (to avoid accidental misoperation). � When each item is set, the process starts then the unit shifts to the upper layer. (When NO OPRT is determined, the unit will shift to the upper layer without doing anything.) � When data are set to be backed up, if the digital EEPROM has not been adjusted, do the operation of LED pattern No. 7.
72
1 2
PDP-436PE
3 4
|
|
|
> |
|
