|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This manual is for the usa model only. But it is clear
, accurate and comprehensive, including board layouts and schematics.
I found it extremely useful for my mitsubishi dp-86da, but the same diagram would also work for the realistic lab5000 and hi fi 80. Thanks.
;
Great to have extra resources for Service Manuals, Now days you can really not trouble shoot efficiently without one , Wayne at IRIONS TV & ELECTRONICS REPAIR Clearwater , Fl. 33755 727-446-7955
 ;
For five bucks you can barely buy a hamburger. Or for the same five bucks you can buy a service manual. Much more useful. (and better for your health, depending on where you buy your hamburgers).
Yes, there are free manual sites out there, but if they don't have what you want, you have to pay.
And five bucks isn't much. Not for full specs, schematics and adjustment and parts replacement procedures.
My only criticism is that grayscale illustrations aren't well rendered, but I've seen worse.
Schematics and text are clear.
I'll be happy to purchase from here again.
Mike
[email protected]
;
Impressively thorough. Even the simple operators manual helped me "fix" one of the 2 CD players in the unit. This unit reads CD's from the top so they should be installed in the magazines "upside down" from typical CD players. The CD player service manual helped me unjam a stuck carriage because somebody transported the box laying down loaded with CD's. A little lens cleaning & the player now works well! Thanks for you help at a great price! Joe
;
I was skeptical at first but later found the manual to be good quality for the price. It took a couple hours to receive the email with the download link, well worth the wait. Thanks.
5
6
7
8
7.1.5 CANCELING DETECTION BY THE TRAP SWITCH � Canceling detection by the TRAP switch
Outline: For video data transmission from the Media Receiver to the plasma display, digital signals are used. Therefore, this unit adopts the HDCP (High-bandwidth Digital Content Protection) system for copyright protection. This unit is also provided with a detection switch (TRAP switch) that will prohibit the unit from being turned on again if the rear case of the unit is opened, in order to prevent the panel technology from being leaked out. Function: To deactivate the detection of the TRAP switch Purposes: 1. During production of this unit, adjusting with the rear cover opened is possible. 2. During servicing or repairing, diagnoses of the assemblies are possible while the power is on. Methods: For setting, use RS232C commands: TSN: Ignore the monitoring of the switch CTM: Clear the detection log of the switch TSY: Reactivate monitoring of the switch Notes:
� � � � � The TRAP switch is located on the chassis (see Fig. below). Once rear case opening is detected, send the TSN and CTM commands. Because the TSN command is not stored in memory, monitoring of the switch can be reactivated by turning the unit off then back on. The same setting is possible using the Factory menu. Because the output of the DVI receiver is controlled by the physical setting of the TRAP switch, if the TRAP switch is set to OPEN, the DVI signal cannot be output even if the TSN command is sent. � When the Media Receiver is connected, detection by the TRAP switch can be canceled by entering Factory mode.
A
B
¶ How to enter Factory mode using the remote control unit Please refer to the technical documentation (Service knowhow). ¶ How to clear the detection log of the TRAP switch In the INITIALIZE layer, hold the OSD key on the remote control unit pressed for at least 3 seconds. ¶ After a power-down, to cancel detection of the TRAP switch using only the remote control unit, follow the procedures below. First, fix the TRAP switch to its depressed position. Set the drive ON/OFF switch in the DIGITAL VIDEO Assy to OFF, Then enter the Factory mode. Press the MUTE key four times, then hold the OSD key pressed for at least 3 seconds. Set the AC switch on the panel to OFF. The log is also cleared. Then set the drive ON/OFF switch to ON.
C
D
Rear View
E
TRAP switch
F
Fig. TRAP switch
PDP-504PU
5 6 7 8
63
|
|
|
> |
|
