|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Good-quality scans. Detailed description. I hope I can repair the machine.
;
High-quality scanning. Detailed description. Recommend for all technician. A+++
;
This is a good quality scan of the original Service Manual from Nordmende, Germany. Contains the circuit diagram, PCB layout, adjust/tune instructions as well. It is NOT in English but in GERMAN language! That was quite right for my german friend from the lower east side in Berlin.
 ;
Received via e-mail this PDF manual is worth the money. This is a quality scan of a manual in excellent condition and is just as good as having the original manual in hand. I have later seen the original manual and it was printed in colour, but this particular manual is black & white but scan resolution is high end quality! All drawings and pictures are presented in great detail. So, nearly perfect score in my opinion.
If you own the turntable you also should own the manual!
;
I was very satisfied with the service manual I ordered and downloaded. I will definitely buy again from this seller.
5
6
7
8
6. ADJUSTMENT
A
Procedure for turning ON the power
1. Connecting the system
(1) Using the system cable, interconnect the plasma display and the AVC system. (2) Connect the plasma display to the AC power source. (3) Connect the AVC System to the AC power source.
2. Procedure for turning ON the power
(1) Turn ON the AC power switch located on the plasma display. The power indicator on the plasma display will start blinking in red. (When the AC power switch on the AVC System is not ON, the power indicator on the plasma display always blinks in red.) (2) Turn ON the power switch located on the AVC System. The power indicator on the AVC System will be illuminated in green. Simultaneously, the power indicator on the plasma display will change from blinking in red to illumination in green. Now the system has started up. (3) If the power indicators on the AVC System and on the plasma display are both illuminated in red, press the power key located on the remote controller and the power button located on the plasma display. The power indicators on the plasma display and on the AVC System will change from red to green. Now the system has started up.
B
C
Procedure for upgrading the AVC System software
(1) With the power being OFF, open the top cabinet of the AVC System and then set the slide switch from the NORMAL position to the WRITE position by inserting an insulated stick into the cutout located between the WHITE port on the rear of the shield case for the PC I/F unit and the RS-232C port. (Or the software may be upgraded by calling the process adjustment mode and using CENTER PROG UPDATE on the process adjustment menu screen. This is discussed later.) (2) Connect a program-installed PC to the AVC system using the RS-232C cross cable. (For the details of the program, see Appendix.) (3) Open the MS-DOS window on the PC and then go to the directory in which the software is installed. (4) Start up the system to which the AVC System and plasma display have been connected. (5) Run �vup.bat (tentative name)� at the MS-DOS prompt. The software will be upgraded. (6) Load the file �civic_XXXXa.bhx main.bhx osd.bhx (tentative name)�. It will take a couple of minutes until the file has been loaded. Never turn OFF the power or operate the system during this rewriting period. (7) After the file has been loaded, turn OFF the plasma display and the AVC System, and then return the slide switch in the above step (1) back from the WRITE position to the NORMAL position. Now the software has been upgraded.
D
Procedure for adjusting each part of the AVC System
1. The adjustments were made to the best settings at factory. If any setting deviates or if any readjustment is regarded as necessary when any part has been replaced, perform the following steps. 2. Any parameter that has been changed in the process adjustment mode is stored on the memory. If any readjustment is required, write down the current value before changing it. 3. Use a stable AC power source. 4. If the program is upgraded, it will take approximately 1 minute for the EEPROM to be initialized before any video appears. Therefore, you will need to wait for this time period. Do not turn OFF the power or operate the system during the period. 5. If the program is rewritten, preferably write down the parameters that have been changed within the process adjustment (see �OSD menu and parameters displayed at manual adjustment�), initialize the EEPROM, and then reenter the recorded values.
E
F
PDP-R03U
5 6 7 8
99
|
|
|
> |
|
