|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It was magic after so many years to still be able to source this info. It was equally amazing to return my Pioneer receiver to it near new sound quality AFTER NEARLY 30 YEARS! Thank you for this ability!
;
Very quick and easy website to use and fast download of manual, quality of manual is excellent and will be pleased to use this service again in the future, thanks so much!
 ;
Easy and secure way to get a complete service manual of a vintage hifi component. Only some parts of the print copy are dificult to read. Nice price!
;
The manual is an excellent reproduction with complete schematics, made troubleshooting and repair a simple process.
;
Up to now you are the BEST! Prompt-efficient and so reasonable ! I have been after SONY service manual for quite some time !Thank you very much ! I can recomend your service to
all my collegagues ! V.Bergfield .
5
6
7
8
6. ADJUSTMENT
A
Procedure for turning ON the power
1. Connecting the system
(1) Using the system cable, interconnect the plasma display and the AVC system. (2) Connect the plasma display to the AC power source. (3) Connect the AVC System to the AC power source.
2. Procedure for turning ON the power
(1) Turn ON the AC power switch located on the plasma display. The power indicator on the plasma display will start blinking in red. (When the AC power switch on the AVC System is not ON, the power indicator on the plasma display always blinks in red.) (2) Turn ON the power switch located on the AVC System. The power indicator on the AVC System will be illuminated in green. Simultaneously, the power indicator on the plasma display will change from blinking in red to illumination in green. Now the system has started up. (3) If the power indicators on the AVC System and on the plasma display are both illuminated in red, press the power key located on the remote controller and the power button located on the plasma display. The power indicators on the plasma display and on the AVC System will change from red to green. Now the system has started up.
B
C
Procedure for upgrading the AVC System software
(1) With the power being OFF, open the top cabinet of the AVC System and then set the slide switch from the NORMAL position to the WRITE position by inserting an insulated stick into the cutout located between the WHITE port on the rear of the shield case for the PC I/F unit and the RS-232C port. (Or the software may be upgraded by calling the process adjustment mode and using CENTER PROG UPDATE on the process adjustment menu screen. This is discussed later.) (2) Connect a program-installed PC to the AVC system using the RS-232C cross cable. (For the details of the program, see Appendix.) (3) Open the MS-DOS window on the PC and then go to the directory in which the software is installed. (4) Start up the system to which the AVC System and plasma display have been connected. (5) Run �vup.bat (tentative name)� at the MS-DOS prompt. The software will be upgraded. (6) Load the file �civic_XXXXa.bhx main.bhx osd.bhx (tentative name)�. It will take a couple of minutes until the file has been loaded. Never turn OFF the power or operate the system during this rewriting period. (7) After the file has been loaded, turn OFF the plasma display and the AVC System, and then return the slide switch in the above step (1) back from the WRITE position to the NORMAL position. Now the software has been upgraded.
D
Procedure for adjusting each part of the AVC System
1. The adjustments were made to the best settings at factory. If any setting deviates or if any readjustment is regarded as necessary when any part has been replaced, perform the following steps. 2. Any parameter that has been changed in the process adjustment mode is stored on the memory. If any readjustment is required, write down the current value before changing it. 3. Use a stable AC power source. 4. If the program is upgraded, it will take approximately 1 minute for the EEPROM to be initialized before any video appears. Therefore, you will need to wait for this time period. Do not turn OFF the power or operate the system during the period. 5. If the program is rewritten, preferably write down the parameters that have been changed within the process adjustment (see �OSD menu and parameters displayed at manual adjustment�), initialize the EEPROM, and then reenter the recorded values.
E
F
PDP-R03U
5 6 7 8
99
|
|
|
> |
|
