|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Response is a little slow- I had to wait 12 hours to receive download link but it says that it may take up to 24hrs.
Manual is old and was not produced in PDF- scanned copy is exellent.
Overall- value for money- I recommend
 ;
Excellent quality and quickly delivered manuals at a fair price. Great care is taken in the reproduction process. Even photographs and highly detailed drawings are as clear as in the original. That cannot be said for some freelance manual copies I have obtained from the web. If you have exhausted your internet search of technical manuals, try Owner-Manuals.com. If they do not have it, I do not think it exists. Perhaps, if requested, they may be able to find it. Their resources are certainly greater than most. Shopping here certainly beats waiting for months or years for the manual you seek to appear in an internet auction or garage sale.
;
Very detailed product, also it is a scanning from original, very useful if you have to service this type of amplifier ! Very good product, very hard to find!
;
the Manual was made available as promised, the scans were excellent..Good Work !!!
;
It's complete and helpful manual with good quality of scan. Thanks very much.
1
2
3
4
1. REASSEMBLY AND DISASSEMBLY PRECAUTIONS
A
1.1 GRILLE ASSY
The Grille Assy is secured to the baffle plate with two-sided tape and bosses. When removing the Grille Assy, if is necessary to wear cotton gloves.
tape. Press the bosses into the baffle plate and press the entire grille into position.
1.2 WOOFER(Disassembly)
The woofer is secured to the baffle plate with four screws from the inside. To remove the woofer, first remove the baffle plate.
Disassembly
Remove it from the under side. 1. Insert the tip of your gloved finger into the gap between theGrille Assy in front and the corner of the baffle plate so that the Grille Assy is slightly lifted.
B
Reasassembly
When reassembling the woofer, place it so that its + terminalis is facing downward. Tighten the screws to the baffle.
1.3 TWEETER(Disassembly)
The tweeter is secured to the baffle plate with two screws from the inside. To remove the tweeter, first remove the baffle plate.
Reasassembly
When reassembling the tweeter + terminal fces outside.
Network Assy(Caution)
2. Insert the gloved finger to the extent of the second joint into the gap between the cabinet and the Grille Assy. When removing the Network Assy, pull it out a little at a time from alternate sides, because it is seated tightly.
C
1
2 1
Input terminal
3. Alternately and gradually lift the left and right sides of the Grille Assy by about 5 cm, sliding gloved fingers along the cabinet. When lifting the Grille Assy, be sure to lift the left and right sides alternately, but not both sides simultaneously.
When reassembling it, apply a adhesive to the screws. Network ASSY
D
Note: Be careful not to bend the Grille Assy too far. Otherwise, it may be damaged. OK : Good example NG : Bad example
Baffle Assy(Caution)
Grille ASSY
When reassembling the cabinet and the baffle plate, secure the screws in the order shown in the figure below:
13 10 8 6 4 3 2
E
OK
Grille ASSY
12 11
9
7
5
1
NG
F
Reasassembly
Remove the old two-sided tape attached to the rear side of the Grille Assy and the front side of the Baffle, and adhere new twosided 2 PDP-S64
1 2 3 4
|
|
|
> |
|
