|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The AKAI 1720 model reel to reel tape recorder described in this Manual is quite an old unit - circa late 1960's. As a consequence, the description of the mechanical details - and adjustments thereof - is quite critical. The manual does this quite well. The schematics are also well presented and have detailed PCB overlays. Probably the only negative is that some half-tone detail has been lost from the original manual as it has been scanned in simple B&W.
 ;
Perfect source for service manuals: fast and professional transaction; high quality, perfect readable and largely scaleable PDF; complete schemes, diagrams and spare part list. Tnx a lot, cu again!!!!
;
I got your link from a friend and I must say that I am really satisfied with your service. Specially this B&O manual I didn't find anywhere on the web... but you could deliver it :-) . You deliver very fast and the copy is of good quality. So your webpage is bookmarked. Thanks
;
This was the Sony CCU-500A Service manual I was looking for.
The price was reasonable.
The permission to download was quck.
I will use Owner-Manual.com for all my manual needs.
;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
Wiring when mounting to the bottom case /
Details for screwing down the CNGD, CD2, and crown washer to Preparations for the optical engine power supply case are based on the diagram below. Screw down the circular
diagram.
(2) Screw down and wire CNGD, CD2, and CNSH to the power supply block
under the CNGD lead.
ZTP7
(3) Screw down and wire CNSH to the taping it, hook it on CNGD at a 45 degree angle CNGD
duct hook. Pass CN1 lead CN1 as in the diagram. AC metal of the filter circuit board
CNGD
fan surface and round terminal of the
terminal of the CNGD at (1) Attach and wire the CN1 angle indicated on the A f r p a s i n g t h e When connecting the CN1 Area of importance PBS fan over connector, securely lock it. Bend the lead rivet part of
(4) Fasten cable pullout portion of the PBS PBS fan with tape
fan
CNGD
To I/O metal CD2 Power supply case
angle so that they do not touch as in diagram on the left Filter unit CNGD
90±10°
Side of power supply case (perspective from Side A) the duct and power supply case,
CNSH Position each round terminal at an
CD2 Power supply case
A
hook
between ribs of the bottom case, To lamp door switch while making sure that they do not protrude by trailing them along the base Style CNGD, CD2, and CD1 wiring as in the
CN1 Stick tape on the place of
To the filter unit FEB1 Style the CN1 and CNGD leads so that they are inserted
20mm from the fastener.
CN1 (Due to a possibility of the optical performance deteriorating
PJ-TX300(C11H2)
32
ZTP6 arrow as shown in the diagram
diagram above. To ensure that they do not run up caused by the optical unit changing shape from pinching) rib (area with diagonal lines) on the side of the power supply case, make sure they do not stick up from base of the bottom case. (To prevent pinching with the exhaust duct.) Leave FEB1 close to side of the power supply case.
TSW
ZTP2 part of the aluminum holder, as in
Tape connector lead of the panel fan diagonally to the curved ZTP6 taping position
(To prevent it from being pinched into the bottom case boss)
CNBAR the diagram below.
Pull CN1 cable in the direction of above, then secure it with tape.To rib (area with diagonal lines) on the fan side of the power supply case, make P a s t h e C N S H sure they do not stick up from the base under the CNPOW, f h b m c a s . ( T o p r v e n t TSW cables, on the pinching with the exhaust duct.) side of the power
CNPOW CNSH ensure that they do not run up on the
Panel
As the lead wire will supply case. be pinched with the Pass the panel fan cable through bottom case, keep it positions indicated on the diagram above. separate from this part.
Wiring diagram 3
|
|
|
> |
|
