|
Who's Online
There currently are 5986 guests and 4 members online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
I was having a hard time finding the problem with this Mackie 1604 unit. I didn't have a schematic. Went looking on the web and found your site and the price was more then reasonable. Ordered it and within the hour had the manual and within 15 minutes had the unit fixed. Best $4.99 I ever spent. Thank you.
Doug
;
This is a service manual in every sense of the word ( French and German versions of the text are included, as well as English..)
There are explanations of the mechanical and electrical functions, plenty of mechanical drawings, and the needed schematics. The quality of the scanning is excellent - all the component values are clearly legible - and very usefully there are pcb component layouts, so you can find a component on the schematic, and then very quicky pinpoint its physical location on the relevant pcb.
I cannot see how I can give this manual any less than the maximum 5 stars! Great value for money, which will pay for itself immediately. Excellent all round!
;
the manual is great and especially hard to find... thanks for the great service and having a hard to find manuel_
;
Please tell us what you think and share your opinions with others. Be sure to focus your comments on the product. You will receive $2.50 of store credit for Your review.
;
hat alles sehr gut geklappt. Das Servicemaual ist gut zu verwenden. Die Pläne und Schrift
ist klar und leserlich. Außerdem preiswert. Grüße an alle Hifi-Bastler
5
6
7
8
7.1.5 CANCELING DETECTION BY THE TRAP SWITCH � Canceling detection by the TRAP switch
Outline: For video data transmission from the Media Receiver to the plasma display, digital signals are used. Therefore, this unit adopts the HDCP (High-bandwidth Digital Content Protection) system for copyright protection. This unit is also provided with a detection switch (TRAP switch) that will prohibit the unit from being turned on again if the rear case of the unit is opened, in order to prevent the panel technology from being leaked out. Function: To deactivate the detection of the TRAP switch Purposes: 1. During production of this unit, adjusting with the rear cover opened is possible. 2. During servicing or repairing, diagnoses of the assemblies are possible while the power is on. Methods: For setting, use RS232C commands: TSN: Ignore the monitoring of the switch CTM: Clear the detection log of the switch TSY: Reactivate monitoring of the switch Notes:
� � � � � The TRAP switch is located on the chassis (see Fig. below). Once rear case opening is detected, send the TSN and CTM commands. Because the TSN command is not stored in memory, monitoring of the switch can be reactivated by turning the unit off then back on. The same setting is possible using the Factory menu. Because the output of the DVI receiver is controlled by the physical setting of the TRAP switch, if the TRAP switch is set to OPEN, the DVI signal cannot be output even if the TSN command is sent. � When the Media Receiver is connected, detection by the TRAP switch can be canceled by entering Factory mode.
A
B
¶ How to enter Factory mode using the remote control unit Please refer to the technical documentation (Service knowhow). ¶ How to clear the detection log of the TRAP switch In the INITIALIZE layer, hold the OSD key on the remote control unit pressed for at least 3 seconds. ¶ After a power-down, to cancel detection of the TRAP switch using only the remote control unit, follow the procedures below. First, fix the TRAP switch to its depressed position. Set the drive ON/OFF switch in the DIGITAL VIDEO Assy to OFF, Then enter the Factory mode. Press the MUTE key four times, then hold the OSD key pressed for at least 3 seconds. Set the AC switch on the panel to OFF. The log is also cleared. Then set the drive ON/OFF switch to ON.
C
D
Rear View
E
TRAP switch
F
Fig. TRAP switch
PDP-504PU
5 6 7 8
63
|
|
|
> |
|