|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
5
6
7
8
� Pattern for each adjustment item Key No. ` Key No. 1
STATIC SKEW
Key No. 4 KEY
Key No. 6 PIN
A
GH
Key No. 7 LIN
Key No. 8 SIZE = Fixed position
B
Key No. ` STATIC
Key No. 1 SKEW
Key No. 4 KEY
Key No. 6 PIN
GV
Key No. 7 LIN Key No. 8 SIZE
C
Note 1: When the Green CRT is replaced, or when the deflection yoke for the green is replaced, prior to the convergence adjustment, tune the center of the image to the center of the screen by turning the centering magnet. Note 2: When the DEFLECTION SERVICE Assy or DIGITAL CONV. Assy is replaced, make coarse adjustment as shown in 3.3 above.
3.4 Fine-adjustment of the Green
Enter MANUAL CONVERGENCE mode by pressing the SET/ENTER key, and make adjustments. Repeatedly make the coarse adjustment as shown in 3.3 if necessary. Proceed with the adjustment for each screen mode. Adjusted values for the green become the standard for the red and the blue.
B
Coordinates where the cursor (adjustment point) is located There are 72 adjustment points (8,9) on the coordinates for FULL and HD modes, but the coordinates actually used for adjustment are as follows (the coordinates outside the ranges indicated below are outside the screen, and adjustment will not have any effect on the screen): FULL : (0, 1) to (7, 9) HD : (0, 1) to (7, 9) (X, Y): X=abscissa, Y=ordinate Some coordinates may be outside the screen and invisible. The point at coordinates (0, 0) is at the upper left of the screen.
D
3.4.1
In MANUAL CONVERGENCE mode entered by pressing the SET/ENTER key, the display becomes as shown below:
Screen indication
3.4.2
F (0 , 0)
Move the cursor to a point to be adjusted with the cursor move keys.
Screen indication
E
A A
Screen mode: F : FULL H : HD
B
F
(4 , 4)
The Screen modes change cyclically with each press of the SCREEN mode key.
Note: The actual shape of the cursor is " [ ] ". The position of the cursor in this figure is different from the actual position on the screen.
F
PRO-730HDI
5 6 7 8
105
|
|
|
> |
|
