|
|
|
Who's Online
There currently are 5753 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
CHAPTER 4 DISASSEMBLY/ASSEMBLY
5.6.2 Replacing the Motherboard
This section includes the procedures required to replace the ColorPASS motherboard. Spare motherboards ship without memory, CPU, and the BIOS chip. The memory, CPU and BIOS chip from the old board will need to be installed on the replacement motherboard. a. To Replace the Motherboard 1. If you replaced the motherboard with a new board, replace the following components on the board: � Memory (see page 4-30) � CPU (see page 4-32) � BIOS chip (see page 4-34) 2. Angle the motherboard so the back panel connectors on the motherboard fit into the cutouts in the back of the tray. See F04-506-02 on page 4-27. 3. Align the mounting holes on the edge of the motherboard (opposite the back panel connectors) with the standoffs located in the base of the tray (see F04-506-02 on page 427). 4. Once the mounting holes in the motherboard are aligned over the standoffs, gently push the motherboard down to secure it to the tray. 5. Insert the 9 motherboard mounting screws to attach the motherboard to the tray but do not tighten them completely (see F04-506-01 on page 4-25 for screw locations). 6. Tighten the 9 motherboard mounting screws. Do not overtighten the screws; doing so could damage traces on the motherboard. b. To Replace Boards 1. Replace the following boards in the appropriate motherboard connectors: � UIB board in the connector labeled PCI1 � Display video board in the connector labeled AGP � Video board in the connector labeled PCI5 As you plug the board into the connector on the motherboard, make sure that the board connector is properly aligned with the connector on the motherboard. 2. Replace any option boards installed in remaining connectors on the motherboard.
4-28
COPYRIGHT© 2000 CANON INC. 2000 2000 2000 2000ColorPASS-Z90/60 REV.0 MAR. 2000
|
|
|
> |
|
