|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
There was no problem at all.After paying i had to wait only a few hours,than i could
download the manual in best pdf-quality.
Thank You !
 ;
I found this service manual to be complete in every detail except for troubleshooting charts. It would be helpful if it had a set of troubleshooting charts; however it is a very good manual otherwise and for the price it is very well worth it.
;
Complete manual included schematics layouts and alignment procedure, clear to read and magnify, extremely pleased with manual and owner manual . com's service
;
perfect, i am very satisfait for the réception of the sansui r-5l service manual, thank you very much
;
Thank you, this is a rare document. Few others have it, but they charge way more for a download.
Great deal (even if you have to wait a few hours to get it).
PT-53WX53G PT-56WX53G PT-47WX53G PT-47WX33G PT-47WXC43G PT-4743G
11. Adjust red centering magnets until the pattern cen-
4. Adjust centering magnets so that the center of the
ter is at the appropriate distance as indicated on figure. 12. Enable digital convergence by changing DAC MUTE from 01 to 00. 13. Set VIDEO �C_OFF� DAC from 02 to 00. Following the adjustment, make sure that all deflection coils are pushed completely toward the CRT cones and that all screws are tightened.
pattern get aligned with screen frame center. 5. Adjust VDEF �V-AMP� DAC until vertical size is proportional on top and bottom. 6. Set DAC MUTE from 01 to 00 (disabling digital convergence). 7. Set VIDEO �C_OFF� DAC from 01 to 00
17.4. NTSC Vertical linearity adjustment
(V-C and V-S)
This adjustment is intended to make the picture vertically proportional (top, center and bottom) for NTSC mode NOTE:
1080i, 480p, 480i pattern can be obtained from Panasonic�s TU-DST51 set-top box DTV decoder. 1. Apply a NTSC pattern that lets adjust the image to correct vertical linearity (see above note). 2. Set VIDEO �C_OFF� DAC from 00 to 01 (to project only green). 3. Set DAC MUTE from 00 to 01 (disabling digital convergence). 4. Adjust centering magnets so that the center of the pattern get aligned with screen frame center. 5. Adjust VDEF �V-C� and �V-S� DAC until vertical size is proportional on top and bottom. Confirm to correct linearity in the middle of the screen. 6. Set DAC MUTE from 01 to 00 (disabling digital convergence). 7. Set VIDEO �C_OFF� DAC from 01 to 00
17.7. HD 1080i Vertical size adjustment (V
AMP)
This adjustment is intended to correct the vertical size of the picture for HD 1080i mode. NOTE:
1080i, 480p, 480i pattern can be obtained from Panasonic�s TU-DST51 set top box DTV decoder. 1. Apply a HD 1080i pattern that lets adjust the image to correct vertical size (see above note). 2. Repeat NTSC vertical size adjustment from step 2
17.5. HD 1080i Vertical linearity adjustment (V-C and V-S)
This adjustment is intended to make the picture vertically proportional (top, center and bottom) for HD 1080i mode NOTE:
1080i, 480p, 480i pattern can be obtained from Panasonic�s TU-DST51 set-top box DTV decoder. 1. Apply a NTSC pattern that lets adjust the image to correct vertical linearity (see above note). 2. Repeat NTSC vertical linearity adjustment from step 2
17.6. NTSC Vertical size adjustment (VAMP)
This adjustment is intended to correct the vertical size of the picture for NTSC mode NOTE:
17.8. NTSC ZOOM Vertical size adjustment (V AMP)
This adjustment is intended to correct the vertical size of the picture for NTSC ZOOM mode NOTE:
1080i, 480p, 480i pattern can be obtained from Panasonic�s TU-DST51 set-top box DTV decoder. 1. Apply a NTSC pattern that lets adjust the image to correct vertical size (see above note). 2. Set VIDEO �C_OFF� DAC from 00 to 01 (to project only green). 3. Set DAC MUTE from 00 to 01 (disabling digital convergence).
1080i, 480p, 480i pattern can be obtained from Pana-
sonic�s TU-DST51 set top box DTV decoder. 1. Apply a NTSC pattern that lets adjust the image to correct vertical size (see above note) 2. Change aspect to ZOOM mode. 3. Repeat NTSC vertical size adjustment from step 2
30
|
|
|
> |
|
