|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
;
Very fast and perfect delivery. Clear and well scanned. A lot of work professionally realized.
Again thak you a lot
 ;
This manual is accurate and of high quality. It is only volume 2 of the service manual. This is schematic, parts lists, and exploded mechanical drawings. The theory of operation and the diss-assembly instructions are in volume 1. The unit can be tricky to dis-assemble portions of so the volume 1 manual can be important. The product description of the manual is accurate but it does not say anything about volume 1 and the image of the front page does clearly say Volume 2.
;
Wellll again thank you very much fast and effective. Clear and well done for such an old TV!!!!
;
It has all the information you will need to fix it. The main circuit diagram is only A4 but being a PDF, you can print it to any size - I did it on two sheets of A3 and it didnt lose any detail - just made it readable when pinned up above the bench. I've found the fault, just need to buy some obscure bits to get it going again!
I cant fault the process, I paid for the manual in the morning and it was ready to download by lunch time.
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
TURNTABLE COUPLING REMOVAL
Coupling
1. Remove the turntable motor, refer to "Turntable Motor Removal". 2. Pull the coupling out of the hole in the oven cavity. 3. At that time the turntable coupling will be free. CAUTION: REPLACE THE PACKING AT THE SAME TIME WHEN REPLACING THE COUF1
Packing
T.T.M. support angle
PLING. BECAUSE THE PACKING MAY BE DAMAGED WHEN THE COUPLIN IS PULLED.
RED WHT
Figure C-3. Turntable Coupling
POWER SUPPLY CORD REPLACEMENT
Removal
1. CARRY OUT 3D CHECKS. 2. Remove the one (1) screw holding the green/yellow wire to the cavity back plate. 3. Disconnect the leads of the power supply cord from the noise filter, referring to the Figure C-4(a). 4. Release the power supply cord from the rear cabinet. 5. Now, the power supply cord is free.
Oven cavity back plate Screw Green/ Yellow wire Brown wire
L N TP TL F F2
Re-install
1. Insert the moulding cord stopper of power supply cord into the square hole of the power angle, referring to the Figure C-4(b). 2. Install the earth wire lead of power supply cord to the oven cavity with one (1) screw and tight the screw. 3. Connect the brown and blue wire leads of power supply cord to the noise filter correctly, referring to the Pictorial Diagram.
MOULDING CORD STOPPER
Power supply cord
Blue wire
POWER SUPPLY CORD OVEN CAVITY BACK PLATE
Noise filter
SQUARE HOLE
Figure C-4 (a) Replacement of Power Supply Cord
Figure C-4(b). Power Supply Cord Replacement
OVEN LAMP SOCKET REMOVAL
1. CARRY OUT 3D CHECKS. 2. Remove the wire leads as Positive lock® connector removal above. 3. Lift up the oven lamp from its retaining clips. 4. Now, the oven lamp is free.
Lock Bulb
Figure C-5. Oven lamp
GRILL HEATING ELEMENT REMOVAL
1. CARRY OUT 3D CHECKS. 2. Remove the one (1) screw holding the exhaust duct to the oven cavity. 3. Remove the exhaust duct from the oven cavity. 4. Remove the two (2) screws holding the two (2) terminals of the main wire harness to the grill heating element. 5. Remove the two (2) screws holding the two (2) grill heater angles to the top of the oven cavity. 6. Remove the two (2) grill heater angles from the oven cavity. 7. Remove the grill heating element from the top of the oven cavity. 8. Now the grill heating element is free.
R-734 - 27
|
|
|
> |
|
