|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! Dziękujemy za!
 ;
It answered my question, which was how to load the paper. I did notice that the very end of the manual was not visible.
;
The product manual I received was exactly what I was looking for, delivered painlessly at a very fair price. I can't ask for any more than that.
;
Very well done!!!!! congratulations. It was a bit longer than usual the wiating time even if it was on time (in 24 hours).
;
Last week I bought a second hand BAUKNECHT TRK4850 DRYER. It is a professional machine with many programs and switch options. I feared it would be a huge quest to find a manual. I was delighted when I found owner-manuals.com. After payment I received the file to download the next day already. The quality is great. I am very happy. Thanks!
but kindly the distributions of the operating programs not find in the owners manual,can you help me to understand the operating programs instructions thank you
Reprogramming Oven Settings Programming Heating Times Oven must be programmed to accept power and Power Levels
levels before programming new START pads. Using the control panel template as a guide, follow these steps to program the pita warmer oven control. See last page for template. 1. Cut out control panel picture to place over pita warmer control panel when programming START pads. 2. Place control picture over control panel so �1� pad is centered over HEAT 1 BAG �START� pad and tape into place. 3. Open oven door and press RESET pad. Leave door open during programming process. � If door is closed or RESET pad is pressed again before programming sequence is finished, oven exits programming mode. 4. Press and hold pad 1 for approximately 15 seconds. � After 15 seconds, signal sounds. Display shows �P�. 5. Press Hidden Pad. Using the control panel template as a guide, follow these steps to program the new START pads located under pads 4 and 5 of the template control panel. 1. Open oven door and press RESET pad. Leave door open during programming process. � If door is closed or RESET pad is pressed again before programming sequence is finished, oven exits programming mode. 2. Press and hold pad 1 for approximately 15 seconds. � After 15 seconds, signal sounds. Display shows �P� indicating programming mode. 3. Press number 4 pad.
� Display shows dd:dd4 to indicate that pad 4 is disabled. 4. Press Hidden Pad.
0p : 10
� Displays shows �OP:10�. � �OP� represents optional program mode. 6. Press START pad 5 times until oven shows �OP:61� in the display.
� Time and pad number display. 5. Press 1, 0, and 0 pad to enter heating time. 6. Press MEDIUM 50% pad to enter power level.
WARM
0p : 61
7. Press 0 pad.
0p : 60
� Displays shows �OP:60�. 8. Press START pad to save changes. � Display shows �OP:73� after START pad is pressed. You have now completed programming pad 4 9. Press RESET pad or close oven door to exit for 1 minute at 50% power and 30 seconds at programming mode. 2 100% power.
7. Press TIME ENTRY pad. 8. Press 3 and 0 pad to enter second stage heating time. 9. Press START pad to save new heating times in oven memory for pad 4.
pp pp
:
4
:0
1:00
4
4
|
|
|
> |
|
