I was so happy that the owner's manual was available. It is well written and helped me to use the radio/CD player/recorder without problems. Thanks for making it available.
Irene Lambert
Thanks so much for the Owner's manual for my Sony PS - FL1. I had purchased the turntable off of eBay. It came in and looked great. Packed well and appeared to be great. I balanced and aligned the tone are and hooked it up. When trying to play a record the tone are would move to the right place and just before it would drop to play it moved back off the edge of the record before touching down. I searched the net for an answer to this issue. No luck. Then I purchased the owners manual and sure enough there was a place to adjust where the stylus touched down. That adjustment solved the problem and saved me a $35 feet to have the player checked out. The manual is well written and easy to understand. It is a must have for anyone with this front loading Sony turntable.
Some years back I pruchased a Sansui G-9000. I had it cleaned up and a problem with the left channel repaired. When I got it back I hooked it up to my tape decks, turn tables, TV and it played great. The only thing I was not really satisfied with was the performance of my Graphic Equalizer. I purchased this owner's manual had poured myself a cup of coffee. The manual is well organized and written in plain language. It also contained the solution to my dissatisfaction. By using the preamp connections coupled I was able to run everything through my graphic equalizer and now enjoy the full potential of my complete system.
An excellent service for the price, however, it would also have been handy if the troubleshooter pages were included. The manual is only sent in the language of your country, thus it looks as though there are some pages missing. Otherwise highly recommended.
Text excerpt from page 10 (click to view)
MOUNTING INSTRUCTIONS
RM2351-2354
We recommend to mount the panel on the door before the refrigerator is installed in the enclosure. To mount the panel, follow these steps: 1. Slide the panel from the bottom of the door into the grooves on the vertical edges of the door . 2. Push the panel upwards. 3. Put the two plastic panel stops (from the parts bag) in the two holes at the lower door frame. 4. Put the decoration strip across the door and fasten it with three screws (from the parts bag).
Snap in
To mount the panel, follow these steps: 1. Open the door 90 degrees. 2. On new refrigerators, the decoration strip are taped inside the door; if installed on the door, remove the door decoration strip (2) by gently pushing the four tabs away with a �at blade screwdriver (1). 3. Insert the vertical edges into the grooves of the door frame (3). 4. Push the panel downwards so that the lower horizontal edge of the panel (4) is �tted into the bottom grove (5). 5. Snap in the decoration strip (2).
1
2
RM2451-2454-2551-2554-2652-2662- 2663-28522862 & NDR1062
With screws
To mount the panel, follow these steps: 1. Open the door 90 degrees. 2. On new refrigerators, the decoration strip is taped inside the door; if installed on the door, remove the door decoration strip (2) by removing its three screws (1). 3. Insert the vertical edges into the grooves of the door frame (3). 4. Push the panel downwards so that the lower horizontal edge of the panel (4) is �tted into the bottom grove (5). 5. Put the decoration strip across the door so that the gap is covered. Secure the decoration strip with the three screws removed in step 2.
2
1 2
1
1
1
1
1
3
3
4
5
REFRIGERATOR REMOVAL
Before removing the refrigerator: � Verify that the AC and DC voltage leads are disconnected. � Shut off the gas supply. � Disconnect the gas supply line at the rear of the refrigerator. Always use a back up wrench when loosening and tightening connections. To remove the refrigerator, follow these steps: 1. Cap the gas supply line. 2. Loosen the screws anchoring the refrigerator to the enclosure. 3. Slide the refrigerator out of the compartment. Replacement is the reverse of removal. When reinstalling the refrigerator, make sure the sealing strips are properly positioned. Check all connections for gas leaks. - 10 -
