|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Delivery came quite promptly and in a very readable format. Thank you.
;
I found my Clarion VRX8370R in the Camper I bought and I wasn't able for month to understand it.
The Owner Manual was perfect and just what I was searching for.
Thank you.
Leonardo
;
Very good copy of Manual, clear and easy to print off, arrived very promptly and reasonably priced.
Thanks, I will use you again.
;
Zeer duidelijke afdrukken op A4-formaat , zeer uitgebreide handleiding . Pluspunt ,zeer snelle
respons van jullie , binnen de 24h . Top !!!
;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
If the memory of the remote is already full, the USE MODE button flashes 8 times in quick succession and the remote automatically exits the learning mode.
Selecting the mode of the remote
You can switch the command mode (AV1 or AV2) of the remote. If the command mode of the receiver and the remote is different, you cannot use the remote to operate the receiver.
6
Tip
Repeat steps 1 through 5 to program up to 10 IR codes.
If programming is unsuccessful, check the following: � If the USE MODE button does not light up in step 1, the batteries are weak. Replace both batteries. � If the USE MODE button lights 4 times in quick succession in step 3, an error has occurred. Start again from step 1.
1 2 3
Press ?/1 while holding down USE MODE. Move the easy scroll key to select �MAIN�, then press the key to enter the selection. Move the easy scroll key to select �AV1� or �AV2�, then press the key to enter the selection.
To cancel programming
Press USE MODE during any step. The remote automatically exits the macro setting mode.
To delay the output of an IR code
Start over from step 1. In step 3, press the easy scroll key lightly (for less than 2 seconds). A 1 second delay is programmed. The USE MODE button lights twice slowly, then the remote automatically exits the macro setting mode.
The USE MODE button lights once (or twice for AV2), then the command mode switches.
To set the 2nd zone mode (North American models only)
You can use the remote to select the input for the 2nd zone. You can use the easy scroll key only for the 2nd zone.
To clear the programmed IR codes
Clear each macro step individually. In step 3, press the easy scroll key for more than 2 seconds. The IR code is cleared. The USE MODE button lights twice slowly, then the remote automatically exits the macro setting mode.
1 2
Press ?/1 while holding down USE MODE. Move the easy scroll key to select �2ND�, then press the key to enter the selection.
The USE MODE button lights once, then the command mode switches.
To start macro play
Move the easy scroll key to select �M1� or �M2�, then press the key to enter the selection
Note
To reset the remote to factory settings
Press ?/1, AV ?/1, and MASTER VOL � at the same time. The USE MODE button lights 3 times, then goes off.
If the Macro Play function does not work properly, program a delay between each operation. See �To delay the output of an IR code�.
14GB
|
|
|
> |
|
