|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It is wonderful done!!! a great job in scanning the manual. Superior quality in all the electric scheme. Very understandable and net!!! Thank you!
 ;
muy buen manual por lo completo de este algunos esquemas estan muy divididos lo que hace algo dificil el seguimiento.
;
very good manual, with detail and clarity in esquematic diagrams and waveforms .
;
Very quality copy of original service manual, which contains the circuit diagrams, PCB and lists of components, well as recommendation for calibration procedures of device, also everything else, that need for repair, tuning and use this oscilloscope.
All presented copies have high-resolution, so you can view all in detail.
This manual will very useful for simple owners and for repairers.
I recommend these manual, because myself is owner of Philips PM3216 and I need sometimes servicing these oscilloscope (principally calibrating).
Also, these document is an example of excellent design of technical documentation.
;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
No.
Item
Measuring instruments & Input signals � IN MEGA chart (precisely scanned size) � Oscilloscope (H-rate)
Mode
Measuring point ( * ) Adjustment parts ( - ) Adjustment level ( + )
Adjustment procedure
2
Frequency response adjustment
� BARS swtch: � R Channel OFF * See Measuring Point � Menu No. 2A Table. LENGTH: - VR202 (R FREQ) 20 M [Main board] + Same levels of the 6 MHz section � G Channel * See Measuring Point Table. - VR302 (G LEVEL) [Main board] + Same levels of the 6 MHz section
6 MHz
1. Shoot the IN MEGA chart so that it becomes precisely scanned size. 2. Connect oscilloscope CH1 and CH2 as shown in the Measuring Point Table. 3. Adjust so that the levels of CH1 and CH2 of the 6 MHz sections are same levels.
4. Adjust in the same way as the R Channel.
CH1 Same level CH2
� B Channel * See Measuring Point Table. - VR402 (B LEVEL) [Main board] + Same levels of the 6 MHz section
2.6
INTERCOM LEVEL ADJUSTMENT
For intercom operation using headsets, the intercom levels can be adjusted with the following controls. � Camera : INCOM LEVEL control on the adapter at the rear. � RM-P210 : INTERCOM LEVEL control on the front panel. Although adjustments on the circuit board are usually unnecessary, perform the following adjustment if the amplification gain seems to be insufficient. 1 Side tone adjustment (Feedback of the microphone to the earphone of the same headset) Headset � S602: 2W [Main board] * INTERCOM jack on the 1. Connect 560 � resistance across H and C INRM-P210 front panel TERCOM terminals on the rear panel. - VR15 (2W S.TONE) 2. Plug the headset into the front panel INTER[Main board] COM jack. 3. Talk and adjust to optimize the side tone level. (Adjust it to the clockwise direction.)
2
RTS side tone RTS headset adjustment (U model only)
� S602: RTS [Main board]
* INTERCOM jack on the 1. Connect 220 � resistance across H and G INRM-P210 front panel TERCOM terminals on the rear panel. - VR16 (RTS S.TONE) 2. Plug the headset into the front panel INTER[Main board] COM jack. 3. Talk and adjust to optimize the side tone level. (Adjust it to the clockwise direction.)
2-5
 $4.99 RM-P210U JVC
Owner's Manual Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
|
|
|
> |
|
