|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
;
The owners manual for the Pioneer VSX-D603S was exactly what I needed. I received it in a timely manor and it was priced fairly. I definately will use your servise again. Thank You
;
This is a great manual. It was easy to read and very accurate. The size of the manual is small so email is no problem. I highly recommend it. The manual is very hard to find other than this website.
1. INTRODUCTION
CONTROLS, CONNECTORS AND INDICATORS (Continued)
8 this button switch camera positions automati� Press and hold to control FOCUS operation of the camREMOTE CONTROL UNIT RM-P2580
$ [AUTO PATROL] button � [FOCUS NEAR, FAR] FOCUS control buttons
cally in a order and at preset time intervals. era lens.
SETUP POWER
CAMERA POSITION
NEAR: Brings a near object in focus. The POSITION display be-
MENU SET AUTO F-1 F-2 F-3
9 POSITION FAR : Brings a distant object in focus. 0 pressed and held for about 1 second, a short beep is genduring AUTO PATROL.
CAMERA POSISPEED
ALARM
KEY LOCK
� AF (AUTO FOCUS) When the NEAR and FAR buttons are simultaneously comes as shown on the left
LENS CAMERA/POSITION PAN/TILT erated and the object is automatically brought into focus.
TION
� 1 2 3 ! NOTE
The AUTO PATROL function can be set on a per-camera AUTO FOCUS function, this function is not available
OPTION CLOSE IRIS OPEN
1 2
If camera being selected does not incorporate the ¤ 4 5 6 @ basis.
AUTO NEAR FAR
FOCUS
AF PAN PATROL
� REF. : �AUTO PATROL OPERATION� on page 15.
7 8 9 even when the short beep is generated. Be sure to use
/HOME
#
0 this function while observing the monitor screen. WIDE ZOOM TELE CLEAR ENTER [�, +] Negative and positive buttons
%
Press button to decrease increase the camera or position number. [IRIS CLOSE, OPEN] Iris control button.
)
¤
Press and hold to control the lens iris. CLOSE : Closes the lens iris. OPEN : Opens the lens iris.
^ [AUTO PAN] button
Press this button to rotate or swing a camera between pre-
( * & ^ % $ set positions at a preset time interval.
POSITION
� [SPEED] Speed button and indicators
The POSITION display bePress to set speed of the ZOOM and FOCUS control
comes as shown on the left CAMERA button Numeric key buttons � MONITOR OUTPUT 1 connector � on the rear panel out0 * Low Medium : High speed �AUTO PAN OPERATION� 14. ing. REF. : �CAMERA SELECTION� on page 10.
[AUTO] [CAMERA] button operations. 8 0
during AUTO PAN. When this button is pressed, unit enters the AUTO SEPress when selecting a camera. QUENCE mode, in which indicator lights up and To select a camera, use the following buttons:
put the camera video signals according to automatic switchENTER button & .
REF. : �AUTO SEQUENCE OPERATION� on page 13. Each press of button changes the operation speed.
! [POSITION] & [ENTER] button
[F1, F2, F3] Function when selecting one of position numbers preset Press to enter a figure input using the numeric key buttons 9 NOTE
These buttons are used for the present. Do not touch them.
REF. : �POSITION SELECTION� on page 11. U model These buttons are valid only when SW-D7000/SW-D8000 ( [CLEAR] button frame switchers are being used. @ [OPTION 1, 2] Press to clear an input figure before it is entered by pressWhen this unit is operated in the B mode, these buttons These buttons are used for present. Do not touch ing the ENTER button. can control certain functions of the specific frame switcher them. model connected to this unit. The RS-232C control is in) [ZOOM WIDE, TELE] ZOOM control buttons volved in this control operation. # [PAN/TILT] control lever Press and hold to control ZOOM operation of the camFor details, please consult your dealer or JVC-authorized Operate the lever to pan horizontally) or tilt (swing era lens. service agent. vertically) rotary turret of a camera. WIDE: Zooms out and widens the image. REF. : �APPLIED SYSTEM (B MODE)� on page 22. 8(Up) : Tilt lever this direction to tilt rotary TELE: Zooms in and narrows the image.
When power turned on, the operation speed is for the camera. . * E model To select a position, use the following buttons: medium. POSITION button � EN[1 to 0/HOME] Numeric key buttons ! * TER button . Use these buttons to choose a camera or position number. &
F1: Single-screen select switch turret upward.
Press button output a single-screen video from 9(Down) : Tilt lever in this direction to tilt the rotary the frame switcher. turret downward. The camera number can be selected using the numeric :(Right) : Tilt lever in this direction to pan the rotary keypad, etc. turret toward the right.
F2: Split-screen select switch ;(Left) : Tilt lever in this direction to pan the rotary
Press this button to output a split-screen video from turret toward the left. the frame switcher. REF. : �MANUAL OPERATION� on page 12.
F3: LIVE/PLAY switch While a menu screen displayed, this lever is used to REF. : �MENU OPERATION METHOD� on page 26.
select or to set an item. Press this button to switch between the playback video of a time-lapse VCR and the camera video.
E-6 E-7
|
|
|
> |
|
