|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
-.
Removing crisper and crisper cover
Model RTlZDC
I Lift slide out then the back,
To remove cover:
1, Lift the front, then the back. 2. Pull up and out. 1, Fit cover notches on back of cover into back nubs on wahs of refrigerator. 2. Lower front into place.
To replace cover:
Ice cube trays
(RTlZDC and RT14DK)
the tray
Remove ice by slightly twisting with both hands.
NOTE: The longer ice cubes are stored, the smaller they get. Slow evaporation is caused by the movement of cold air.
. Cubes left in the bin for long periods of time may develop an offflavor, like stale water. Throw old cubes away. Cubes may also become smaller if stored for a long time. . Good water quality is important for good ice quality. It is not recommended that you connect the ice maker to a softened water supply. If a softened water supply cannot be avoided, it is important to maintain the water softener so it operates properly. Water softener chemicals, such as salt from a malfunctioning softener, can damage the ice maker mold and lead to poor quality ice.
Automatic ice maker
To remove crisper:
1. Slide crisper straight out. 2. Replace in reverse order. Model RT14DM includes a factoryinstalled ice maker. The ice maker is an optional accessory for model RT14DK.
Changing the light bulb
To remove cover:
1, Lift back, then slide to the rear until the front can be lifted.
2. Lift cover up and out.
To replace cover:
1. Slide the front cover tabs in from the rear of the front supports on the refrigerator walI.5. 2. Lower back of cover into place. Connect the ice maker to the water supply before turning it on. The ON/OFF lever is a wire signal arm. Lower signal arm to make ice. Raise signal arm to turn off the ice maker. Freezer must be cold enough for the ice maker to work. This may take eight hours or more before the correct temperature is reached. �First� ice may be discolored or offflavored because of new plumbing connections. Throw away first few batches of ice. Change ice cube size with the, dial or lever on the side of the ice maker. Ice crescents are normally attached at the corner. They break apart easily. Normal sounds include water running when the ice maker is working and the thud of ice as it falls into the bin. If ice is not being made fast enough and more ice is needed, turn the Refrigerator Control to a higher number. Wait 24 hours, and if this does not increase the ice supply, turn the Freezer Control to A. Raise the signal arm before you remove the ice bin. When you replace the bin, push it in ah the way. Then lower the arm to the ON position.
Electrical Shock Hazard Unplug the refrigerator or disconnect the main electric power supply to the refrigerator before changing a bulb. Failure to do so can result in electrical shock or injW.
Models RTllDK and RTllDM
Lift the front. then the back.
1. Disconnect refrigerator from power supply. 2. Remove the bulb from the socket located behind the Control Console and throw the burned-out bulb away. 3. Replace with a 40-watt appliance bulb. 4. Reconnect power supply.
stop. Lift the front and pull again. To remove crisper:
1. Slide crisper straight out to the stops. 2. Lift the front. 3. Slide crisper out the rest of the way. 4. Replace in reverse order.
NOTE: Not all commercial appliance
bulbs will fit your refrigerator. Be sure to replace a bulb with one of the same size and shape.
Page 5
|
|
|
> |
|
